6G Celicas Forums

Welcome Guest ( Log In | Register )

> New Brake Master Cylinder Needed??, diagnosis inside
post Apr 11, 2020 - 6:35 PM
+Quote Post
BonzaiCelica



Enthusiast
*****
Joined Apr 24, '08
From Orange County, CA
Currently Offline

Reputation: 33 (100%)




I replaced my brake master cylinder with a new Raybesto unit as well as a new proportioning valve (OEM). My problem is I will get air pockets 5 min into driving, pedal sinks momentarily and then brake feel is back to normal

While bleeding brakes, once i crack a caliper open, air bubbles do not come out till about 10 seconds later.

-Booster Operating check OK
-Booster Air Tightness check – engine off OK
-Booster Air Tightness underload OK
-No Leaks at Banjo Bolts
-Soft Lines OK
-No rust between shims and pads
-Caliper Pistons Seals not torn or leaking
-Caliper Pistons move freely when pressed inward with bleeder valve open


--------------------
For Sale Items:
 
Start new topic
Replies
post Apr 16, 2020 - 2:55 AM
+Quote Post
BonzaiCelica



Enthusiast
*****
Joined Apr 24, '08
From Orange County, CA
Currently Offline

Reputation: 33 (100%)




never said anything about sticking brake pads.

i swapped calipers left to right and right to left. the right caliper is still having the issue where it bleeds air pockets no matter how many times i bleed it. ordering one now!!!


--------------------
For Sale Items:
post Apr 17, 2020 - 10:22 AM
+Quote Post
Bitter

Enthusiast
*****
Joined Mar 11, '06
From Way South Chicago
Currently Offline

Reputation: 0 (0%)




QUOTE (BonzaiCelica @ Apr 16, 2020 - 2:55 AM) *
never said anything about sticking brake pads.

i swapped calipers left to right and right to left. the right caliper is still having the issue where it bleeds air pockets no matter how many times i bleed it. ordering one now!!!

You can't swap calipers side to side, that would put the bleeder port below the fluid inlet making it impossible to bleed out all of the air. laugh.gif I actually see this once or twice a year at work and after you've been burned by it once yourself you'll never forget.

Did you bench bleed the master cylinder before installing it? Did you bleed in stages after it was installed? By stages I mean first you bleed at the master cylinder and it's two lines by cracking one open, pedal down, close line fitting, repeat repeatedly until no bubbles, then do the other line fitting the same. Then bleed at the ABS pump inlets and outlets if it has ABS (you mentioned a prop valve so probably non ABS), you can bleed at the prop valve inlet and outlets just the same though, THEN bleed at each wheel. You may need to do 'surge bleeding' where you pump the pedal 3 times and hold it down hard then someone opens the bleeder, sometimes that pulsing pressure motion breaks air loose from where it's stuck. Also sometimes you'll need to bleed with power assist using the surge bleed method to get enough fluid velocity to push little bits of trapped air out.

Finally, if you're using a 'one man' brake bleeder and not doing a final 2 person bleed then that's probably the source of the issue. The one man bleeders work about 90% of the time to get about 90% of the air out. Vacuum bleeding is great to get the process started and mostly done, but it almost never gets all the air. Pressure bleeders ($$$) are closer to 100% but expensive and wasteful, meant for high volume production and big shops, but pretty effective because they can get high fluid velocity. However I would always suggest following up with a manual bleed just to make sure.


--------------------

Posts in this topic


Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: March 29th, 2024 - 12:28 AM