6G Celicas Forums

Hey there, I've got a 5sfe in my 95 GT with 157k, I would let it go for cheap. I hit a deer and kinda ****ed up the front end of the car but the engine still runs, and it's still strong, nothing wrong with it at all. I have paper work for the work that was done to the top half of the motor before I got in the accident. If you would want to come to my place and pull the motor out and I would give it to ya for 500 bucks, 600 if i pull it, 700 for the whole car with the premium alloy wheels, and it would need to be towed. I have an engine hoist as well. I live in wisconsin, my cell is 262-327-7098 if you want anymore info about it, really would love to get it out of my driveway

So, the drivers side bearing is seized up inside the knuckle and its in there pretty good and i cant manage to get it out even with a press. So im wondering if i can just swap my suspension parts from my GT95 to my ST97, like even just the steering knuckle and the lower ball joint, etc.. if i would need to replace Both sides of the car or if i can get away with just the drivers side? any info is appreciated, im trying to get this car back on the road so i can sell it. anyone interested, they are both for sale, clean titles.

I have a 97 ST LM and a 95 GT for sale or trade. Will part out the GT, ST will be sold as a whole. Motor in ST: 197 original, GT: 154 original, 3000 on rebuild and I've got receipts. the GT has some of the parts swapped over to the ST, but nothing important. The ST runs and I have replaced the front wheel bearings, rear breaks, exhaust manifold, clutch, front support bar (beneath bumper liner), headlights, tweeters (total of 6 speakers now), TWM short shifter, indiglow cluster overlay with controller, JVC deck wired for subs. As for the GT, bout two years ago i got into an accident with it and crunched the front end a bit, the damage was: the coolant lines, windshield(which i replaced), air bags deployed, radiator punctured, passenger side relay, headlights were removed, and the frame where the headlights and radiator is slightly bent inward. the radiator was pushed up toward the heat shield on the header and didnt go any further, so nothing with the engine was damaged so its basically a parts car, has all u need to swap to the ST if you're ambitious enough. I live in wisconsin and would prefer to sell to someone close by, can PM me for any more info you may want.


http://imageshack.com/a/img538/3936/P4m6V0.jpg
http://imageshack.com/a/img913/6669/lyUeZi.jpg
http://imageshack.com/a/img673/4008/GpZdxC.jpg
http://imageshack.com/a/img909/5172/8tWGQh.jpg
http://imageshack.com/a/img909/3233/XLNq0D.jpg
http://imageshack.com/a/img661/1018/aVqcPi.jpg
http://imageshack.com/a/img540/5159/mtO7P1.jpg
http://imageshack.com/a/img661/4496/UT3six.jpg

bump still lookin for a celica in either wisconsin or surrounding areas. 94-99 doesnt need to be running.

Hey, I live in wisconsin, lookin for a local seller. The car does not need to be a certain color, just needs to be intact aside from engine, and have no prior collisions. I prefer a manual transmission but I would settle for an automatic... its a simple conversion anyway. Depending on condition, price I'll be willing to pay will vary. send me PM and I will get back to you as soon as possible.

okay, i was kinda thinkin that.

So i was cruisin home one night doin about 85 and hit a deer... Looking to buy a new front clip cuz thats rly all thats messed up besides the windshield, hood, coolant lines, radiator, fans, right headlights. Once i got under the hood, I noticed that the front support bar was bent inward about 8 inches, so I just wanna replace the front end.
Does anyone know how much it would run me to get the front clip, windshield and hood?

So, my wiring harness is in terrible condition and i need a new one, i went to replace the alternator today and noticed the plug was snapped and corroded SO i have no idea where else to get a wiring harness. if anyones got one in good condition i would be interested. pm me with ur price.

Menomonee Falls area