6G Celicas Forums

Hey I can come pickup, how much for the radiator?

well the header flange and gasket meet right where the first cat goes. so in order to make the height of everything to fit, the first cat would need to be removed. i dont know if i misread your post or not, but i didnt know if this was understood. it has the o2 bung, im just not sure if anything would go wrong if i take a cat out.

hey guy, i have a header i wanted to install on my 94, 7a-fe, and it has 2 cats. with the new header i need to knock out the first cat. but from the engine it goes o2 sensor, cat, o2 sensor, cat, then just exhaust. i was wondering if keeping the o2 sensors in the same spot and taking out the first cat would do anything like make it run worse or anything even as little as the check engine light. im from pa, and we dont have emissions testing so im not worried about that, just the fact of re-selling it if i ever decide to, or just general concern. any advice would be great. thanks!

so the side that goes into the trans, after the cv joint there is a seal that comes out and could be replaced? like the section that itself goes into the tranny and the cv boot, theres a seal that goes behind the boot that meets the tranny?

hey guys, i need to replace an axle, and was wondering if there was a seal on the cv joint where it meets the transmission. i dont have photo to use but right where the passenger side axle goes into the tranny, the back of the cv joint, is there a seal or something i should replace when i replace the axle/cv joint? or is there no seal or anything at all?

do you know what the last one is? power steering, alt. and water pump. those are the two i know. ande how would you change the third one?

im still new to workin on cars, so im trying to learn all i can, but where is the pwer steering assembly? like is it right under the belt, so i can get to it easily with the tire off? and will it be like the tensionor for the alternator?

i was wondering if anyone had a link or could just tell me, is the tensioner under the alternator in a st the tensioner for all the belts? i have the 3s-fe and wanted to replace all the belts. i know the waterpump and alternator belt use the alternator tensionor, but i wasnt sure if that would loosen the other two to replace, or if there was another tensioner for the power steering one

my friend is putting on a car meet, and i was hoping to get some celicas there too. i dont think a lot of us will go but i would like to see some. pm me for directions, may 25, or heres a link with the details.
facebook event

i know this is a dumb question but im still kinda new to the site, where are the stickies?

is there anyway to do that without going to a garage? i know not to let them spin at all, but if they happen to, is a garage the only place to do that?

so when i change the timing belt, if the gears spin a little, my engine will be fine? wont be out of time?

i was just trying to find if the 7a-fe engine was non interfering with the pistons and valves for a timing belt change. i only did a little bit of research and just decided to try on here. if anyone can help that would be great. thanks

so would that mean if yours is a 94 st and mine is too miine will be the same, or will they make 94 st's- some with one cat,and some with two?

do you hapen to have any that will? im looking to try to get a new set of everything

will all of these work on an 7a-fe?

ok well just let me know

ok, can i get a like percentage of how much use there is on it?

how much would you want for it before you do any work

i have an st 94, and the trannys all original

how much would you want for the strut bar to 16354

just trying to look for some clutch kits better than OEM. got ripped off by buying parts on ebay so im trying to stay away from there. but anyone got anything worth lookin at?

really? well thats not exactly what i wanted to hear lol. thanks though guys

sorry, but that confused me a little. so your saying i might need to mod the headers i bought to get them to fit? and will the first cat fit in with the new headers?

just an idea