6G Celicas Forums

Does it matter what ecu you use auto or manual ? My car acts like it has a rev limiter at like 40 mph . I was thinks it's the turbo map sensor I don't have that

I have bleed the lines a hundred times, we just unbolted the slave cylinder from the tranny and put the cylinder with the line on it on the fender so we wouldn't have to bleed it . But we bled it anyways and when when the car is off it will go into all gears. When it's on it won't go into gear with the clutch peddle pressed in you have to slam it into gear .. and it grinds but if you slam it into gear it takes off and then dies right away . Somthing is wrong I just need help figuring it out . Someone said to adjust the peddle or it's the pressure plate is bad or clutch is on backwards but I've never heard of that

Hello I've mad tons of post about my Celica 3sgte gen 4 swap, I finally put it all together and started it in almost done . Unfortunately when I put my axles in and everything else and went to put it into gear the clutch isn't disengaging and letting the car move the slave cylinder and master cylinder is fine I think it's the pressure plate or clutch disk I did buy used .. can someone home me figure out how to tell if it's bad ? Like the pressure plate or clutch disk ? And I kinda was thinking I put the disk in backwards I mean is that possible?? Please help

Can anyone help me figure out the part number for the serpentine belt ? On the gen 4 please iv been looking and I thought I found the right one but I ordered it and it wasn't even close .. if anyone can help me on this I would really appreciate it I'm so close to being done !

Hello I know I have been making alot of threads but thanks to you guys I now have the 3sgte in my celica ! With a few more things and it's done ! Just curious what's the best way to run the intercooler ? Do I need to cut holes or anything I've been looking at it but just curious before I start I already have the intercooler just need help it's front mount btw thank you all !

Do I 100% need a turbo map sensor the one that is plugged into the intake ? I was told I can just go away with it and do it direct

What down pipe and exhaust should I go with I'm doing a 3sgte 4th gen swap a Celica 6gen

Do you run the hood full time no issues ?

But with the carboon hood is had hood scoops look https://m.ebay.com/itm/VIS-94-99-Celica-Car...%257Ciid%253A10

Hello just curious alot of people say to run front mount intercooler for the swap do to better cooling and more breather room just curious I have a vis racing carbon fiber hood with vents for my 97 Celica and I'm talking about a 4th gen but could I run that and maybe hood risers I'm not trying to be cheap I simply like the intercooler being on top ? Any advice

I can't be that hard .. i feel like people just don't want the headache I just wanted some pointers and maybe help from someone who's done it

I am trying to do the wiring on my 5sfe to the 3sgte 4th gen need some help !

So what I need to do is get a 3sgte flywheel and use my clutch kit for my 5s tranny and I'm good thats what I got idk if I'm not grasping it but I know I'll have to run a stage 2 at the least for the 3s engine

So in other words I need a 3sgte flywheel with bolts and a 3sgte pressure plate and needs to be modified to go to the splines for the 5s and south end makes them I cant find them on eBay or anything like that ? What the place called so I can give them a call so what do they all do for me I have to buy the 3sgte flywheel and that make the pressure plate for me with a clutch kit to fit my 5s and I use my throw out barring ? Correct

So thats all I need to keep it stock for right now ? Depending on the engine and stuff I will most likely replace and buy new parts not trying to insult anyone's knowledge at ! So with my 5sfe tranny I was going to buy a 3sgte flywheel and the bolts and fun a stage 2 clutch kit for my tranny but I'm a little confused on the pressure plate like the 3s because I'm using my 5sfe tranny . Shouldnt I just use the 3s flywheel and then use the clutch kit and pressure plate for my tranny ? Or does it have to be custome made ? And so I'm looking at fuel pump , flywheel , clutch kit pressure plate, wiring(which I might attempt myself) and I'mma get a few gauges that I need is that all I need to run it stock ? Thank you guys so much I'm learning so much !

I am going to be using my 5sfe tranny but I realize now I need the flywheel for the 3sgte and since I'm using the 5sfe tranny I need a clutch and pressure plate for my tranny(5sfe) thank you for the diagram and help. What else do I need for the swap ? Like I know the basics I got I need the harness, flywheel, fuel pump . What else just to run the car stock ? Im sure I know more I just can't think of it right now

I see I see I was going to try and do the harness myself I have two 5sfe harnesses from the same year both 97. But I'm a little worried I might mess up but I just need help with figure out what I need for my swap to run it stock I know I need the harness done then flywheel and pressure plate so I'll need the clutch kit . But I'm running my stock 5sfe tranny with the 3sgte so I'm confused on the pressure plate thing . But that's what people say I know I might need a fuel pump and a intercooler thats all I know for now and we'll of course some gagues

Does this work with a 3sgte 4th gen ??

I am using the stock 5sfe tranny for my car and I was told I need a flywheel and pressure plate for my 3sgte engine is that okay ? And as far as the intercooler goes I was told I was okay using just a filter and stuff for now but some people say it runs to hot .. I'm not really sure I can't say i know like everything that why I need help and I wanna learn iv been doing tons and tons of research everyday thank you for helping me !

I have the 3sgte 4th gen engine on the way and getting things ready to go! Looking for help and ways to get it going ! Right now I have done alot of research and talked to tons of people. I was wondering if I could get some help with my project . Right now I'm planning on running the engine stock I made sure it came with the 3sgte hanress and ecu and im getting a flywheel and clutch kit . Iv been looking around and doing research and I might attempt my wiring harness myself I have two harnesses and I might just try it . But I also need help from people that have experience with the swap and the 6gen community. Helping me find parts, and help me get it on the road with a wonder build ! I hope this goes well , would appreciate all the help I can get !