6G Celicas Forums

ill be done up here in may, but i know all the roads back in princeton..........

btw where is this strip?

omg were nearing 100 pages!!!

This post has been edited by Celiracer18: Feb 4, 2009 - 9:54 PM

Come on lets get there. People need to post more on updates to their cars. Like Rick..

Well I'll be getting some hood gas dampers, cooling plate, and strut tower brace to start off this year's mod. Then down the road maybe intake, header, exhaust....lol

What is the first meet gonna be for this year?

How much you want for it?

Heres an updated list.

Performance:
Custom Short Ram Intake
Tanabe Exhaust
Vincent Doggy Cooling Panel

Suspension:
Tanabe Springs 2.2" drop Front and 1.5" Rear
Stainless steel braided brake lines all around
TwosRus endlinks

Exterior:
USDM Dealer Option Side Skirt
Spoilerless, I think I'm going to put it back on.

Interior:
Alpine UBS Deck

This post has been edited by 99GT: Feb 5, 2009 - 7:07 AM

The strip is on the way to Lake Carlos. I don't remember it, but it's like a street you have to go on to get to Lake Carlos.

Lake Carlos has so MANY large mouth bass also. I swear every minute you catch a good size bass. I go with my bro in law catch and release.

heres a mod list for you.

SOLD!!!!!!!

Hey joe how hard was it to install the stainless steel brake lines ?? Since I'm gonna be doing pretty much a whole brake parts tune-up brembo rotors,hawk pads, Super blue brake fluid, ebrake shoes etc... might as well upgrade the brake lines too if its not to much of a hassle. I also have ST sway bars waiting to be put on with new twosrus endlinks, tenzo r springs, bilstein shocks, jdm tails, etc... can't wait till summer hits.

Bilstein shocks? Really? You don't think they will ride a little rough with the tenzo springs? Brake lines aren't hard. Just make sure you get wrenches made for brakes. It will be a hell of a lot easier. I think the bleeding part is going to be hard. Just follow the BGB and you'll be golden. Remy, when are you ever meeting up with us man?

Remy is easy. Just a few nuts and bolts. Plug and play, you can't mess us haha.

I had a issue with the brake line tab. IRC the there was a tab that was a bit too long. I just turned it the other way not using the tab until summer.

The one I got was similar to the one third from the left. When you take off your brake line you'll see.

It was off just by a little, but that little margin makes a big difference with the brake fluid squirting with that much pressue.

I just turned it the other way around.

why not goodridge?

Thats just a picture for reference.

The tenzo springs are 1.8 drop all around after a whole lotta research I think bilsteins will probably be best. Will you can meet up with me I'll need someone to help sand my car this summer LOL.


Good to know joe, I might get the stoptech ss brake lines. Thanks

O really? You just need me to do the sanding? Not helping out with a 3s swap or anything.

No 3s for me yet will be doing bodywork I need to get it done before the rust spreads...the 3s can wait. What did you use to sand your car anyways ?? I'm not talking about sandpaper either lol

The compressor will cost me a pretty penny too cant do both still looking for a DD too.

This post has been edited by Remy: Feb 6, 2009 - 11:05 PM

Don't bother with a compressor. Without the right compressor and duty cycle one you'll be screwed with air tools. Get a long sanding block and a short sanding block and go from there. Don't go with too much of a heavy grit sand paper either. You don't want to gouge into the paint. Besides you just want the dents sanded down to the metal and clean body parts just sanded from clear.

Use your hand, and make sure you wash the car off after sanding to see missing spots and what not.

Hey Joe, a six pack of heineken and the knock sensor is yours. I'll install it for free and split the six pack with ya...

I plan on spraying my own car and hopefully learn from it thats why I wanted a compressor. The dent kinda popped itself out not as bad as it was before maybe because of the weather lol I'm gonna try to hammer it out as much as I can and go from their. I really wanted to get the 3s first but gotta fix that rust first its just surface rust noting major yet so better to get it done now don't wanna wait and see what it turns into.

You got it man. When will you be open? I'm not open today. Free sunday after 12:30. Free after 5pm on the weekdays.

Sunday works for me, or any evening during the week.