Check out my 3SGTE motor Options

[ToysRfast]

I think it needs some cleaning and a few new things like gaskets, belts, spark plugs for sure. and the do you guys think about the exhaust manifold? That one is real rusty. thats what the front clip looks like. Here is some of the stuff I think I might need. Can anyone tell me what this thing is? And here is the exhaust manifold and the crazy oil leaking from engine there is also orange stuff on the engine that seems to be coming from some where?

[soulshadow]

1.) looks like a noise filter.
2.) that orange stuff is called gasket sealent.
3.) You should smack the place you bought the clip from cause it looks terrible, leaking oil in the valve cover and obviously rusty. Im sure it has 100K miles already.

This post has been edited by soulshadow: Mar 30, 2006 - 9:49 AM

[ToysRfast]

What does it do? Do I need it?

[ToysRfast]

There are 115135 on it is that miles or kilometers? I guess I have to fix the engine up it's gonna cost more then I thought it would have. I should have just bought the engine and wasted my money that way

[snapshotgt]

How much did you pay for it?

~snap

[presure2]

#1 is the resistor packs for the injectors and fuel pump, yes you need them

[x_itchy_b_x]

just give that manifold a little love and care. wire brush it then send it out to be powder coated. or chromed lol

[Vacchus]

I am afraid that you will have more troubles than the exterior problems of this engine.. It seem that it had very tough times when it was united with the rear cut..

[BBoYRuGGeD]

There are 115135 on it is that miles or kilometers? I guess I have to fix the engine up it's gonna cost more then I thought it would have. I should have just bought the engine and wasted my money that way

thats in km so its around 72k miles.

bboy

[bufferdan]

Its not bad...what manifolds arent rusty? Someone just used some orange RTV to try and seal the valve cover. Just replace the gasket and get a twosrus allen bolt kit to tighten it down.

[ToysRfast]

I payed 1400$ for the front clip.

[x_itchy_b_x]

also i wanna say replace EVERYthing you can.
water-pump, distributer, plugs, fuel filter,belts, esp the head-gasket if needed.
do a compression check just to make sure. that will show you a definite leak but a compression test wont help if the hole is very small and only leaks with boost,
much more psi would have to be pumped in the cylinders to check for such a small hole.
also check for any signs of oil and coolant mixing. like the underside of the oil cap. look for a milky substance. almost like an oil and coolant milk shake.
when you have the exhaust manifold off check to see if the ports coming out look normal (covered in black carbon) and not squeaky clean,
if one port is extremely clean compared to others than that cylinder has coolant entering it.
also check the old coolant, if there is any still in the radiator for oil.

im just saying that from experience. it sucks to have to redo things when the motor is already in.
take what the people who sold you the engine say with a grain of salt.

This post has been edited by x_itchy_b_x: Mar 30, 2006 - 12:07 PM

[jgreening]

also i wanna say replace EVERYthing you can.
water-pump, distributer, plugs, fuel filter,belts, esp the head-gasket if needed.
do a compression check just to make sure. that will show you a definite leak but a compression test wont help if the hole is very small and only leaks with boost,
much more psi would have to be pumped in the cylinders to check for such a small hole.
also check for any signs of oil and coolant mixing. like the underside of the oil cap. look for a milky substance. almost like an oil and coolant milk shake.
when you have the exhaust manifold off check to see if the ports coming out look normal (covered in black carbon) and not squeaky clean,
if one port is extremely clean compared to others than that cylinder has coolant entering it.
also check the old coolant, if there is any still in the radiator for oil.

im just saying that from experience. it sucks to have to redo things when the motor is already in.
take what the people who sold you the engine say with a grain of salt.

I say replace the turbo too with something bigger.

[ToysRfast]

I know what the head gasket is but what is a the esp?

Thank I will get what I can done with the engine.

[x_itchy_b_x]

oh esp is my abbreviation of especially. since the head gasket is a vital gasket.

[ToysRfast]

Oh ok THANKS

[ToysRfast]

Can someone tell me more about what type of clutch I need for the swap? I use the 5SFE tranny with the 3SGTE motor. I ask because I just called Spec preformance clutch and the guy put me on hold and never answered the phone again

[playr158]

yea you should contact a different person from spec
READ the stickies

"Lagos wrote:
Clutch:
if using the gt tranny with the 3sgte motor, you will need:
5sfe disk (or a custom made 3sgte disk, with the splines for the 5sfe tranny)
5sfe throwout bearing
5sfe alignment tool
3sgte pressure plate
3sgte flywheel (or just get your stock one resurfaced)"

[ToysRfast]

The the 3sgte flywheel will work with the 5sfe tranny?

[playr158]

yes..