![]() |
![]() |
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
someone please help today i installed my system and for some reaon my amp wont turn on i ran everything the right way, what could be wrong? Can someone help me on this issue what could be the issue or issues? please can someone help me on this, Thanks
|
![]() |
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined Aug 15, '10 From The Best Coast Currently Offline Reputation: 12 (100%) ![]() |
make sure your fuse is plugged into the power line. Make sure it isnt blown. Also check the fuse on the amp.
should be: battery-->fuse--->amp (low gauge) amp--->GOOD ground (low gauge) amp---->head unit (rca and high gauge turn on lead) amp---->subs/speaker (mid gauge) Make sure its hooked up to the battery post well.. edit: i know this may be dumb but just double check all connections..make sure + is in + and - is in -..ect... This post has been edited by SupraKid: Oct 2, 2010 - 10:13 PM |
![]() |
|
![]() Enthusiast ![]() ![]() ![]() Joined May 29, '09 From Lake Ariel, PA Currently Offline Reputation: 4 (100%) ![]() |
I guarantee you the remote wire isn't spliced into the correct wire behind the head unit.
-------------------- ![]() Representing the Convertible Crew since 2008 |
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 10, '10 From MA Currently Offline Reputation: 37 (100%) ![]() |
|
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined Mar 16, '09 From New York Currently Offline Reputation: 23 (100%) ![]() |
Agreed as well, most common thing messed up.
If you just touch the power wire to, both the remote and power for a second, the amp should turn on. If not look at the grounds and fuses ![]() -------------------- |
![]() |
|
Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 29, '09 From Gainesville, FL Currently Offline Reputation: 17 (100%) ![]() |
If all wires are hooked up correctly, check your positive terminal lead. Ground is most commonly the problem, or a fuse.
If you do not have the protectant on the post, there tends to be a white build up. This will ruin the surface area, and put your amp into protect mode, or simply not turn on. Clean the post, clean the connector, and apply the protectant. |
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() Joined Nov 10, '09 From Louisiana Currently Offline Reputation: 5 (100%) ![]() |
99% of the time you didn't hilltops remote wire up correctly or didnt even run it. Check that. And make sure you have it grounded correctly
|
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
my amp is a pioneer it has these following connectors, + power, - ground, and sound control. Where do i hook up the power from the head unit to? also i noticed that were i placed the ground wire i scrapped of the paint real good but the only thing is that the screw that was used there is really rusted could that be it? Or is it the power from the head unit? does the terminals being a little old have to do with anything as well?
|
![]() |
|
Enthusiast ![]() ![]() ![]() ![]() ![]() Joined Jun 18, '09 From Orlando Currently Offline Reputation: 8 (100%) ![]() |
Age of the terminals definitely could play a part, all connections need to be clean. I assume that the connection for the remote wire varies on all head units, so I can't answer that. Try to look it up online using the head unit's model number. Did you also make sure to turn your head unit on?
-------------------- '97 ST \ Eibach \ KYB \ Kenwood \ Alpine \ Cusco \ OEM+ [sold 10/18]
'93 MX-5 LE |
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
so what turns on the amp? the head unit or the power wire running through battery? my question is the power wire that i connect to head unit where in the amp do i connect that wire too?
|
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 10, '10 From MA Currently Offline Reputation: 37 (100%) ![]() |
there should be a connection for the amp turn on wire on the amp right near the + & - terminals...
|
![]() |
|
Enthusiast ![]() ![]() ![]() ![]() ![]() Joined Jun 18, '09 From Orlando Currently Offline Reputation: 8 (100%) ![]() |
so what turns on the amp? the head unit or the power wire running through battery? my question is the power wire that i connect to head unit where in the amp do i connect that wire too? The battery supplies power, but the amp will only turn on when the head unit turns on, which is why the remote wire is necessary. And then the ground provides, well, grounding...those are the three necessary wires for operation. This post has been edited by SwissFerdi: Oct 4, 2010 - 9:47 AM -------------------- '97 ST \ Eibach \ KYB \ Kenwood \ Alpine \ Cusco \ OEM+ [sold 10/18]
'93 MX-5 LE |
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
my amp has a + power, - ground and sound crontrol connector and ofcourse all the other ones for the speakers its a 4 channel amp, so the head unit connector should go to the sound control connector right?
what color wires do you usually hook up the remote wire too on the headunit? the blue ones right? |
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 10, '10 From MA Currently Offline Reputation: 37 (100%) ![]() |
yes the blue one usually used as the turn on signal wire.
can you give me the exact model amplifier you have |
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
GM-X554
|
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 10, '10 From MA Currently Offline Reputation: 37 (100%) ![]() |
the turn on signal terminal is the one to the right of the ground terminal
|
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
oh thanks man so like i was saying my terminals on the battery are a little old can that be the problem? also the screw screwed to the ground wire to my cars chasis is a little rusted as well could that be a problem? one more thing i want to mention, my RCA cables has a remote wire attached to them already and thats what i used as a remote, should that be ok or should i just used a different remote wire?
|
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 10, '10 From MA Currently Offline Reputation: 37 (100%) ![]() |
for right now, i would say the grounds should be fine, just see if it works once you hook up the turn on wire. the one that's connected with the RCA cables will work fine
|
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
i did and it still doesnt work could the amp be burned out?
|
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 10, '10 From MA Currently Offline Reputation: 37 (100%) ![]() |
is there a light on it that lets you know when its on?
|
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
yeah there is a light on there when its on
|
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 10, '10 From MA Currently Offline Reputation: 37 (100%) ![]() |
a way to test and see if it works is to hook up a +12v source to it to see if it turns on. if i could visually see everything, I could easily tell you the problem, and it sucks that i cant. try that test and see if it even turns on
|
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
ill try and take some pics later and post them see if that can help a little better
so if that doesnt make it turn chances are its burned out? |
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 10, '10 From MA Currently Offline Reputation: 37 (100%) ![]() |
not necessarily because something else could be wrong.
I'll give you a set of "IF's" right now: If it does work with the +12v source, then something is wrong with your head unit. If it DOESNT work, then you should clean up all your grounds. If that still doesn't work, then check your inline fuse to make sure it's still good. If that still doesn't work, then check your wires (especially the power wire from the battery) to make sure they didn't rip or tear during installation. And after all that, if it still doesn't work, then it's the amp. If it's the amp, check the fuses on it. If the fuses are fine, then get another amp. If the new amp doesn't work, then something is utterly f***ed up with your car lol |
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
lol alright man i checked all that out and give you an update i appreciate all the help
|
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 10, '10 From MA Currently Offline Reputation: 37 (100%) ![]() |
its no problem at all lol
im hear to help you outt, I had the same problem the first time I was wiring in my subs to my old car (except my problem wasn't as in-depth) |
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined Aug 15, '10 From The Best Coast Currently Offline Reputation: 12 (100%) ![]() |
Where did you get this amp?
|
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
its mine i had it on my truck and now i want to hook it up in my car
|
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 10, '10 From MA Currently Offline Reputation: 37 (100%) ![]() |
any luck with it yet?
|
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
no im actually at work right now i will mess with it later when i get home i did clean the terminals on the battery and will mess with it later
|
![]() |
|
Enthusiast ![]() Joined Sep 27, '10 From Laredo Currently Offline Reputation: 0 (0%) ![]() |
im going to try one more thing imma check the remote wiring, is there a specific one i should use? what would you all recommend?
|
![]() |
|
Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 29, '09 From Gainesville, FL Currently Offline Reputation: 17 (100%) ![]() |
I'm not trying to be a ass, but you need this.
http://www.caraudiohelp.com/how_to_install...l_a_car_amp.htm Amp install is simple. You need power, from the positive terminal from the battery, you need a ground, which is commonly created via the trunk or seat belt bolts. You need a remote wire from the head unit. The wire is commonly labeled as remote. The rest is hooking up speakers. Check battery terminals for ample surface area, and all connections. If it still doesn't work, your amp is fried. |
![]() |
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 10, '10 From MA Currently Offline Reputation: 37 (100%) ![]() |
there's no specific wire for the remote wire, you can use any wire for that. If there is one that runs with the RCA cables then use that one
This post has been edited by mkernz22: Oct 5, 2010 - 12:31 PM |
![]() ![]() |
Lo-Fi Version | Time is now: June 11th, 2025 - 9:34 PM |