Powered by toyota Options

[blackliftback]

http://s1301.photobucket.com/user/krzkon/m...pg.html?filters[user]=136316310&filters[recent]=1&sort=1&o=1

For whats to come.

This post has been edited by blackliftback: Oct 25, 2013 - 9:06 PM

[blackliftback]

Sorry still cant post the pics for some reason

[Batman722]

I spy a Beams from an MR2...

[blackliftback]

Thank you batman.

Just got the engine earlier today. Says on the transport ticket that its a 6 speed? Never heard the beams came 6speed.
Anyway... This should be done in a week or two hopefully

[JoshuaM]

Ohhh, exciting

[richee3]

BEAMS came mated to the S54 transmission, not a 6 speed. Simple mistake. Swapping an MR2?

[njccmd2002]

oh, oh, why from MR2, you have to source the parts to make it fwd..... Did u know that?

[blackliftback]

I have it under control. Hopefully muahahahahahaah

This post has been edited by blackliftback: Oct 26, 2013 - 6:43 AM

[blackliftback]

oh, oh, why from MR2, you have to source the parts to make it fwd..... Did u know that?

It was the closest to not having a chopped up harness. It came with the engine harness going to the ecu. It makes my life a lot easier than getting one thats is chopped up like chinese food

[richee3]

The MR2 harness is different.

[blackliftback]

Understood. It doesnt have the wires going to the under hood fuse box.
It came with ecu but for some reason only 2 of the 4 spots on the ecu have a plug to it.

[kurt95gt]

Sounds like you might just want to buy a beams harness for a celica an be done

[richee3]

Gotcha. As long as you're aware, carry on. I actually have a spare Celica BEAMS harness I'm not using. It's been extended and is fully functional, but not truly finished- it has butt crimps instead of properly soldered splices, and it's missing the VSV plug and oil pressure plug.

[njccmd2002]

as long as your properly informed, and this is not a surpise, then u should be golden.

[blackliftback]

Not much of a suprise. Plus i looked at it and it looks like i "could" use it the way it is and extend the wires to passenger side. The spot where they clipped off, i am searching for a wiring diagram atm.

[richee3]

Moving the alternator, power steering pump, coolant lines, etc. could be a pain. There could be a couple of partouts on the BEAMS Owners Group.

[blackliftback]

Quick update: injured my foot. Swap is delayed. But while my foot is healing. I will be sending the mr2 beams back for their celica beams. Seen they had an uncut harness st202 that just came in. Looked at the invoice and it said this engine was the st202. So i called to complain and they said they will exchange it for me. Awesome!

[richee3]

That's extremely fortunate. I haven't even had a free minute to dig my spare harness out of storage to send you pictures yet. Hopefully your foot heals quickly and you can get started with the swap soon.

[Batman722]

Quick update: injured my foot. Swap is delayed. But while my foot is healing. I will be sending the mr2 beams back for their celica beams. Seen they had an uncut harness st202 that just came in. Looked at the invoice and it said this engine was the st202. So i called to complain and they said they will exchange it for me. Awesome!

Good decision.

[blackliftback]

That's extremely fortunate. I haven't even had a free minute to dig my spare harness out of storage to send you pictures yet. Hopefully your foot heals quickly and you can get started with the swap soon.

Thanks. The idiot that i was working on his rear brake disc swap, decided to start his car to bleed the brakes. Unfortunately, it was in first gear. He let go of clutch, car jumped forward and pinched my foot between my deck and his car.

The invoice also stated it was a 6 speed and i told them it was not haha. So their description was way off lol

[blackliftback]

Minor update.

New celica beams came in and my foot has healed. Its cold but getting ready to start on this project this weekend hopefully

[blackliftback]

Got started on the project today. A few hours and old motor came right out.
Hopefully all goes well tomorrow and beams will be on the road

[richee3]

Don't forget to transfer the engine hook from the passenger side of your 5S to the BEAMS. Took us a couple of hours of fighting to get mine to sit in place properly before we gave up and used the hook from the 5S.

[blackliftback]

Don't forget to transfer the engine hook from the passenger side of your 5S to the BEAMS. Took us a couple of hours of fighting to get mine to sit in place properly before we gave up and used the hook from the 5S.

Thanks for heads up but i never use an engine lift for swaps

[Smaay]

Don't forget to transfer the engine hook from the passenger side of your 5S to the BEAMS. Took us a couple of hours of fighting to get mine to sit in place properly before we gave up and used the hook from the 5S.

Thanks for heads up but i never use an engine lift for swaps

oh you are the hulk and just set it in there by hand?

[blackliftback]

You know it. I hulk it all day

[Box]

He uses his favourite weather hardened oak tree and rope. I'm going to take a guess he just drops everything out from the bottom.

Either way, looking forward to seeing another swapped Celica. It's nice to see them how they're supposed to be. (DISCLAIMER: That includes all engine swaps)

This post has been edited by Box: Dec 4, 2013 - 2:20 PM

[blackliftback]

He uses his favourite weather hardened oak tree and rope. I'm going to take a guess he just drops everything out from the bottom.

Either way, looking forward to seeing another swapped Celica. It's nice to see them how they're supposed to be. (DISCLAIMER: That includes all engine swaps)

Yessir. I drop it out from the bottom. Less hassle of angling it out from the top

[blackliftback]

Finished up some wiring today. Just extending wires for now.

Theres a ignition box on the firewall that the plug on harness doesnt fit. Any ideas?
Then i notice theres 3 vac lines on the engine side on intake mani on the 5s and only 2 on the beams.
Please give me some insight on these things.

This post has been edited by blackliftback: Dec 4, 2013 - 10:30 PM

[blackliftback]

Had to do this and follow the crowd on docs sig pose haha

[blackliftback]

Slacked off for 2 days but got her in now!


Looks like the vvti solenoid is broken.

[blackliftback]

Having a fee issues with plugs and vac lines. Any help will be appreciated. The charcoal canister or whatever you want to call it.... Theres a line that goes to it but dont see it on the beams engine.

[blackliftback]

Ok i have been searching and searching. Can anybody help me with a picture of which pin is which on the EA1 plug please?
I know about the pin 4 and 17 thing. Just don't know which one is pin 4 lol.
A picture with the pins numbered would be greatly appreciated. Thank you in advance!

[Batman722]

some info

http://www.6gc.net/forums/index.php?showtopic=82196

http://www.6gc.net/forums/index.php?showto...3105&st=140

[blackliftback]

Thanks batman! I saw the ea1 plug thread but he used the gt4 chassis plug from clip. Unfortunately i do not have the chassis plug to use. I have a white with black stripe and i forget the other wire, where can i tap these wires to?

The inside splice is done. Thanks to the info batman posted.

[blackliftback]

Ok. I have the beams running. But it runs really rough. When i plug in the maf from avalon, it kills the car.
It runs like it wants to die. When i start it up.. I have to gas it a bit to get it going. Any answers will be appreciated



Lol

Also, first gear only goes til 15mph second gear goes to about 26 mph and third goes to about 39 mph. Havent tried the rest