Feb 17, 2015 - 6:50 PM
|
|
![]() Enthusiast ![]() ![]() ![]() Joined May 13, '06 From Kaimuki, HI Currently Offline Reputation: 10 (100%) |
I got my switch in today from The_enD and it has 8 wires. I opened it up and there is a little circuitboard inside, so I don't want to start probing with my ohm-meter. I can't find a wire diagram for the rear fogs and I don't see a section for the Euro models in bgbonline at celicatech.
-------------------- -Jay
95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other 01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished 02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve |
![]() |
Feb 20, 2015 - 12:46 PM
|
|
|
Enthusiast ![]() ![]() ![]() Joined Nov 21, '05 From Tacoma, WA Currently Offline Reputation: 7 (100%) |
|
Feb 20, 2015 - 1:25 PM
|
|
![]() Enthusiast ![]() ![]() ![]() Joined May 13, '06 From Kaimuki, HI Currently Offline Reputation: 10 (100%) |
I like the information that you put into the thread. My question now is...there are 3 ground wires, are all of them ground all the time or are some of them ground switched? Meaning it would trigger something operated by ground, like the cluster light. -------------------- -Jay
95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other 01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished 02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve |
Feb 21, 2015 - 12:03 PM
|
|
|
Enthusiast ![]() ![]() ![]() Joined Nov 21, '05 From Tacoma, WA Currently Offline Reputation: 7 (100%) |
I like the information that you put into the thread. My question now is...there are 3 ground wires, are all of them ground all the time or are some of them ground switched? Meaning it would trigger something operated by ground, like the cluster light. The other thread that Batman posted has descriptions of the pinouts. One of the grounds is for the illumination and the other two are for the rear fogs. I think they are there to only allow the rear fogs to go on when the headlights and front fogs are on. I didn't get too much into it as I'm planning on using it for front fog lights. |
match220 rear fog light switch wiring Feb 17, 2015 - 6:50 PM
Batman722 This is all I got
http://www.6gc.net/forums/index... Feb 17, 2015 - 10:02 PM
match220 QUOTE (Batman722 @ Feb 17, 2015 - 5... Feb 18, 2015 - 12:56 AM
malpaso Greeting to Hawaii . Mate, the thing is EU modes h... Feb 19, 2015 - 3:04 AM
match220 QUOTE (malpaso @ Feb 18, 2015 - 10:0... Feb 19, 2015 - 3:15 AM
PegGTS QUOTE (match220 @ Feb 19, 2015 - 2:1... Feb 20, 2015 - 12:56 PM

match220 QUOTE (PegGTS @ Feb 20, 2015 - 7:56 ... Feb 20, 2015 - 1:19 PM
malpaso QUOTE (match220 @ Feb 19, 2015 - 9:1... Feb 23, 2015 - 12:21 AM
match220 QUOTE (malpaso @ Feb 22, 2015 - 7:21... Feb 23, 2015 - 2:45 AM
PegGTS I'm actually interested in this as well. I hav... Feb 20, 2015 - 3:12 PM
match220 QUOTE (PegGTS @ Feb 20, 2015 - 10:12... Feb 20, 2015 - 9:09 PM
PegGTS QUOTE (match220 @ Feb 20, 2015 - 8:0... Feb 21, 2015 - 9:17 AM
The_enD 4 pin - mechanical ( basic on / off )
8 pin - elec... Feb 21, 2015 - 11:04 AM![]() ![]() |
| Lo-Fi Version | Time is now: November 23rd, 2025 - 3:24 PM |