 What the Tuck, Wire Tucking the RC |
 Oct 15, 2010 - 9:48 PM
|
 
|
 Moderator  Joined Apr 17, '03 From Rockland NY Currently Offline Reputation: 15 (100%)  |
Hey guys,
So I decided to start tucking my engine bay. I didn't expect to go as far as I am now, but once I started hiding things, I wanted to hide more & more stuff. I'm not going to the extreme like coomer did, just wanted to clean up the motor a bit. Engine before I started the tuck, it was neat, but I wanted to venture further.  I started with the passenger side, because its the easiest.  I had to remove the fenders, front bumper, and eventually the hood. I will get better pics tomorrow, my camera ran out of battery. Here is a blurry cellphone pic of the frame rail tucked.  I'm happy with the results, then the wiring to the alt and O2 sensor started to annoy me. lol So I jumped in on the drivers side Here is some of the tuck and the relocated fuse box  I can't believe how time consuming this is. I have the engine harness out of the car now, I will rewire the entire harness so I can completely hide it. Blurry pic warning, its getting there.  I still have a ton of work to do on it, consider that the almost half way point, still plenty of things to hide and relocate. I have a feeling I'm gonna pull the engine  I will get some better pics tomorrow. Any suggestions ? DEF --------------------  I will return one day. |
 |
Replies
|
Jun 4, 2015 - 8:12 PM
|
|
|
Moderator Joined Apr 17, '03 From Rockland NY Currently Offline Reputation: 15 (100%) |
Bringing this back from the dead. I can't believe its been 5 years since I drove my car. Holy S**T.
I'm slowly putting it back together, I have the harness plugged in from the cabin to the fire wall. The hard part is next, I have a few plugs that need to be identified. I'm not sure if I need them or not. I did away with tucking the harness, just going to clean it up and get the car running. I'm itching to drive it now. I'm going to work on it some more tomorrow night, hopefully have the harness at 90 to 100% installed. If you wiring gurus could look at these pics to help me figure out if i need these plugs back in my harness or not, that would be awesome. I'm going to re-read this thread. I think I asked about these plugs already. Edit: yeah I did ask about some of the plugs. I'd like to rule out the three in the picture
Attached image(s)
-------------------- I will return one day. |
Posts in this topic
Defgeph What the Tuck Oct 15, 2010 - 9:48 PM
jcbass7 lookin good! Its so easy to get hooked on tuck... Oct 15, 2010 - 9:54 PM njccmd2002 this means your not selling and making a comeback?... Oct 15, 2010 - 11:21 PM jordisonjr I'm curious as to how you did this
I know its ... Oct 16, 2010 - 12:46 AM
Defgeph QUOTE (jordisonjr @ Oct 16, 2010 - 1... Oct 16, 2010 - 9:52 AM whatthe Very nice work will keep an eye out for updates to... Oct 16, 2010 - 5:58 AM presure2 lookin good so far man! Oct 16, 2010 - 10:18 AM Defgeph Passenger side
Drivers side
I have decid... Oct 16, 2010 - 4:35 PM jordisonjr Where did you tuck everything?
Under the frame rai... Oct 16, 2010 - 5:10 PM Defgeph QUOTE (jordisonjr @ Oct 16, 2010 - 6... Oct 16, 2010 - 8:35 PM jordisonjr QUOTE (Defgeph @ Oct 16, 2010 - 8:35... Oct 17, 2010 - 1:09 AM njccmd2002 ^^ i think hes doing a wireless conversion.
n... Oct 16, 2010 - 5:17 PM stl95celica AHHH! ive been wanting to do this. looks great... Oct 16, 2010 - 6:59 PM Defgeph I think I'm going with this filter, small blac... Oct 16, 2010 - 9:11 PM Bigblock -8 AN inside diameter is 7/16 or 1/2 inch. Depend... Oct 16, 2010 - 10:14 PM 95CelicaST Word of advice... since I've been there and do... Oct 17, 2010 - 1:03 AM Johnnyny QUOTE (95CelicaST @ Oct 17, 2010 - 2... Oct 17, 2010 - 1:31 AM 95CelicaST Yeah. I thought I waterproofed mine... Water will ... Oct 17, 2010 - 1:37 AM Johnnyny QUOTE (95CelicaST @ Oct 17, 2010 - 2... Oct 17, 2010 - 2:48 AM hurley97 I don't think Jeff needs to worry about water,... Oct 17, 2010 - 9:11 AM SupraKid QUOTE (hurley97 @ Oct 17, 2010 - 7:1... Oct 17, 2010 - 5:20 PM njccmd2002 Move the fusebox to the trunk? Oct 17, 2010 - 10:18 AM Stambo did you already remove the charcoal canister also? Oct 17, 2010 - 10:42 AM Defgeph Charcoal canister was tossed when I did the swap.
... Oct 17, 2010 - 1:03 PM DEATH Awesome job Jeff - I'm very impressed. I still... Oct 18, 2010 - 8:36 AM Defgeph no rush dude, I wont be done for a while. Oct 18, 2010 - 10:48 AM DEATH Hey bro - one thing I do see - stretching the thro... Oct 18, 2010 - 4:40 PM 95st-celica Hey def, this is gonna look great when its done, h... Oct 18, 2010 - 7:30 PM Defgeph QUOTE (DEATH @ Oct 18, 2010 - 5:40 P... Oct 18, 2010 - 9:24 PM Johnnyny maybe a cover for the fuse box Oct 18, 2010 - 9:51 PM Defgeph one more
Two of the wires were already cut i... Oct 18, 2010 - 11:34 PM presure2 neither of those look like the ALT plug to me, jef... Oct 19, 2010 - 7:56 AM DEATH QUOTE (Defgeph @ Oct 18, 2010 - 9:24... Oct 19, 2010 - 8:51 AM Defgeph Take a pic for me I can receive pics, That cable, ... Oct 19, 2010 - 9:48 AM Defgeph Another one, located in the cabin. I think it has ... Oct 19, 2010 - 10:39 AM stephen_lee the triangle 3pin IS infact the alt plug on a 5th ... Oct 19, 2010 - 11:37 AM presure2 QUOTE (stephen_lee @ Oct 19, 2010 - 12... Oct 19, 2010 - 11:53 AM Defgeph QUOTE (stephen_lee @ Oct 19, 2010 - 12... Oct 19, 2010 - 1:22 PM presure2 QUOTE (Defgeph @ Oct 19, 2010 - 2:22... Oct 20, 2010 - 6:44 AM lagos Thats the EB1 plug (if i recall the name correctly... Oct 20, 2010 - 7:19 AM Defgeph I guess I'll just run two separate looms for t... Oct 20, 2010 - 3:43 PM easternpiro1 def. youre my hero. Oct 20, 2010 - 6:25 PM Defgeph Can somebody take a measurement of the engine bay?... Oct 20, 2010 - 9:32 PM azian_advanced RE: What the Tuck Oct 21, 2010 - 1:10 AM EKAn Any updates? Jan 3, 2011 - 12:20 PM Ted95 QUOTE (EKAn @ Jan 3, 2011 - 12:20 PM... Jan 3, 2011 - 4:43 PM ChfNix QUOTE (Ted95 @ Jan 3, 2011 - 3:43 PM... Jan 4, 2011 - 1:18 PM richee3 ^^^ x4. Feb 6, 2011 - 11:31 PM 95st-celica x5...whats the deal def....i want to see this thin... Feb 7, 2011 - 1:18 AM Defgeph Once spring time gets here, I will finish this pro... Feb 7, 2011 - 9:35 AM Defgeph In the process of gathering all parts needed to fi... Apr 11, 2011 - 11:50 AM Ted95 QUOTE (Defgeph @ Apr 11, 2011 - 12:5... Apr 11, 2011 - 12:23 PM purplegt4 QUOTE (Ted95 @ Apr 11, 2011 - 12:23 ... Apr 11, 2011 - 12:30 PM Ted95 QUOTE (purplegt4 @ Apr 11, 2011 - 1... Apr 11, 2011 - 12:43 PM Defgeph Couldn't find out specs on the filter. Still l... Apr 11, 2011 - 12:29 PM Defgeph Here is a link that can handle 150 PSI of fuel , i... Apr 11, 2011 - 12:39 PM Defgeph QUOTE ya now its just a matter of proper fittings ... Apr 11, 2011 - 1:00 PM Ted95 QUOTE (Defgeph @ Apr 11, 2011 - 2:00... Apr 12, 2011 - 3:20 PM Culpable04 stock fuel pressure is 33 - 38 PSI Apr 11, 2011 - 6:53 PM Defgeph Anyone know the size of the banjo connected to the... Apr 12, 2011 - 9:09 AM CoreyST This looks so good, I can't wait to tuck my wi... Apr 12, 2011 - 12:29 PM Defgeph Its should work just as long as the banjo is neede... Apr 12, 2011 - 4:12 PM presure2 They are all 12x1.25 threads Jeff. Apr 12, 2011 - 5:50 PM Defgeph I might just keep the stock filter and lines for t... Apr 12, 2011 - 6:16 PM Ted95 QUOTE (Defgeph @ Apr 12, 2011 - 7:16... Apr 13, 2011 - 9:58 AM Defgeph Just waiting on parts now. Half the wiring is done... Apr 20, 2011 - 10:59 AM Defgeph Need some help guys, two issues so far
The harnes... May 15, 2011 - 7:15 PM DG_Performance water coolant... the middle 16 pin ecu plug... #4 ... Jun 15, 2011 - 9:26 PM Batman722 Bout time mang.
Congrats on getting married !
... Jun 4, 2015 - 8:59 PM Defgeph Thanks Dustin!
I will try to get the rest of ... Jun 5, 2015 - 6:01 AM richee3 Awesome to see this thread revived and see you... Jun 5, 2015 - 6:56 AM Smaay the top plug looks like the noise filter that is m... Jun 5, 2015 - 8:48 AM Defgeph Thanks guys. I"m happy to get back in the gam... Jun 5, 2015 - 4:23 PM Defgeph Need a little help with this wire blue with black ... Jun 6, 2015 - 2:47 PM Defgeph Couple more wires that I need help with.
The black... Jun 6, 2015 - 6:22 PM presure2 blast from the past!!!
good to see you... Jun 7, 2015 - 10:48 AM Defgeph To be completely honest Manny. I'm trying to g... Jun 7, 2015 - 11:15 AM lagos Welcome back Jeff.
I haven't looked at this s... Jun 7, 2015 - 12:20 PM Defgeph Thanks Art,
I have 91 3sgte wiring diagram (my e... Jun 7, 2015 - 8:44 PM Defgeph Just an update, I have the harness in starter work... Jun 8, 2015 - 7:32 PM richee3 I'm not sure if you have these or not, but it ... Jun 8, 2015 - 8:29 PM Defgeph Thanks for the link!
I'm down to one code... Jun 11, 2015 - 5:37 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: July 18th, 2025 - 5:11 AM |