 trying to set up a 3s-ge swap |
 Apr 12, 2004 - 2:21 PM
|
 
|
 Enthusiast  Joined Aug 20, '03 From Annapolis, Md Currently Offline Reputation: 5 (100%)  |
First, has any one done this, or do they just go right to the 3s-gte?? also, gt tranny will bolt right up, but i was told, or read that it wont handle that much power?? its only 177 hp, an 150 trq? is that to the wheel or crank? also what else would i need besides gt engine mounts?? Thanks
also does any one know where else, i could locate, a harness an comp?? This post has been edited by Digndoug: Apr 12, 2004 - 2:38 PM |
 |
Replies
|
Apr 27, 2004 - 6:59 PM
|
|
||
 Enthusiast Joined Dec 27, '03 From Nor Cal Currently Offline Reputation: 0 (0%) |
The harnesses are different between the 7AFE and the 5SFE... so you might not be able to use a majority of the plugs/sensors, etc... because of placement or compatability between the two. The only parts of the stock 7AFE harness you could use, would probably be some plugs that match up... and the wires themselves... for extending/modifying/creating a harness to fit the 3SGE (that's what mike [qatar] does). That's the catch. They probably are similar enough between the 5SFE and 3SGE that you can use a majority of the stock harness... but probably not between the 7AFE and 3SGE. Regardless... there will be a lot of little parts that are very difficult to source assuming you buy just a longblock (ignitor/coils, TPS, AFM/MAP sensor, [depending on what version of the 3SGE] amoungst other little things) so I would reccomend getting a front clip for a swap like this, which people have never really ventured into, nor have much information about... not even to mention your biggest obstacle... the differences in wiring between an A series and S series, which you basically have to make a new harness for (or modify an exsisting 3SGE harness)... -------------------- "It's ok to be naked girl... I'm an artist!"
1995 AT200 Celica ST: stocked out daily driver... 1984 AE86 Corolla GT-SR5: silvertop 20V 4AGE project car jacked up with goodies... 1991 SW2x MR2 n/a: bare bones hardtop model soon to be... |
||
Posts in this topic
Digndoug trying to set up a 3s-ge swap Apr 12, 2004 - 2:21 PM
Doge try and find a ssII or ssIII clip. You will be ab... Apr 12, 2004 - 3:11 PM Chrobis Good luck finding an SS clip... no company I know ... Apr 12, 2004 - 8:30 PM Digndoug well, has anyone done this before, or am i going t... Apr 12, 2004 - 9:15 PM do_0b theres a 3sge on ebay right now but its from a mr2... Apr 12, 2004 - 9:19 PM Consynx there is someone at Celica.net doing either an SS-... Apr 12, 2004 - 9:36 PM Digndoug Im kinda suprised that not that many people do or ... Apr 13, 2004 - 3:36 PM Kwanza26 QUOTE (Digndoug @ Apr 13, 2004 - 8:36 PM) Im kinda... Apr 13, 2004 - 3:53 PM Digndoug hey, im still trying to set up this swap, from an ... Apr 13, 2004 - 7:38 PM celicarocker QUOTE (Digndoug @ Apr 13, 2004 - 7:38 PM) hey, im ... Apr 13, 2004 - 8:01 PM Chrobis I dont think the mounts just bolt in... They would... Apr 14, 2004 - 1:25 AM latinomasfino if anyone is interested in the mr2 engine 3rd gen ... Apr 14, 2004 - 2:43 AM Kwanza26 QUOTE (Digndoug @ Apr 14, 2004 - 12:38 AM) hey, im... Apr 14, 2004 - 4:15 PM Digndoug ok, a few other questions, that i just wanna make ... Apr 14, 2004 - 7:44 PM Kwanza26 QUOTE (Digndoug @ Apr 15, 2004 - 12:44 AM) ok, a f... Apr 15, 2004 - 2:10 AM neoklis Well this discussion is really difficult to follow... Apr 15, 2004 - 6:27 AM Digndoug hey, for this swap, ok, im guessing my fuel pump ... Apr 26, 2004 - 9:32 PM Kwanza26 QUOTE (Digndoug @ Apr 27, 2004 - 2:32 AM) hey, for... Apr 26, 2004 - 10:21 PM macavely ok if you have a GT wouldn't you just need the... Apr 26, 2004 - 11:03 PM Kwanza26 QUOTE (macavely @ Apr 27, 2004 - 4:03 AM) ok if yo... Apr 27, 2004 - 12:28 AM sinner96ST QUOTE (Kwanza26 @ Apr 26, 2004 - 10:28 PM) QUOTE (... Apr 27, 2004 - 1:27 AM Kwanza26 QUOTE (sinner96ST @ Apr 27, 2004 - 6:27 AM)
would... Apr 27, 2004 - 1:36 AM Digndoug QUOTE (Kwanza26 @ Apr 27, 2004 - 6:36 AM) QUOTE (s... Apr 27, 2004 - 4:53 PM Digndoug well say i have it already...... i guess ... Apr 27, 2004 - 8:04 PM Digndoug any one, still need some info, if ya could help???... Apr 29, 2004 - 5:05 PM Kwanza26 Those parts will be very hard to find... but i bel... Apr 29, 2004 - 5:13 PM Digndoug ok, i think im getting more woried and cunfused...... Apr 30, 2004 - 3:22 PM
Kwanza26 QUOTE (Digndoug @ Apr 30, 2004 - 8:22 PM) ok, i th... Apr 30, 2004 - 7:25 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: July 19th, 2025 - 2:53 AM |