Jun 19, 2005 - 10:10 AM
|
|
![]() Enthusiast ![]() ![]() ![]() ![]() Joined Nov 22, '03 From Tracadie-Sheila, NB (Canada) Currently Offline Reputation: 14 (100%) |
is it a good idea to swap my tranny to a mr2-t (since I must change my tranny anyway for a swap) an keeping my 5sfe then saving for a 3rd gen 3sgte? or that tranny are no no with 5sfe? also, if i decide to get a 2rd gen 3s, will the tranny still be compatible?
This post has been edited by HaRv3sTeR: Jun 19, 2005 - 11:03 AM |
![]() |
Jun 22, 2005 - 11:30 AM
|
|
|
Enthusiast ![]() ![]() Joined Jan 8, '05 From Alabama Currently Offline Reputation: 0 (0%) |
ok...the mr2-t tranny is gonna be a very difficult install...its coming out a rwd car so you have to turn it around and get new half shalfts, linkages, and i think reweld one of the mounts on the tranny to a different location...personally if i was doing the 3s swap i would use the 5sfe tranny...its bolt ups just fine and i havent heard of any failing yet under the power of the 3s...as for using the mr2-t..dont put it in now unless ur 5s tranny is dead because its gonna be a definate hassal fitting it into your car..the 5s should bolt up though considering it is an s series transmission and engine combination...so if you plan on using the mr2-t wait till u get the 3s and do it all at once
|
Jun 22, 2005 - 12:00 PM
|
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined Feb 8, '04 From KY Currently Offline Reputation: 0 (0%) |
QUOTE(MonsterBOX @ Jun 22, 2005 - 4:30 PM) ok...the mr2-t tranny is gonna be a very difficult install...its coming out a rwd car so you have to turn it around and get new half shalfts, linkages, and i think reweld one of the mounts on the tranny to a different location...[right][snapback]303004[/snapback][/right] If you have a clip you just use the linkage and stuff from the awd tranny. You don't weld any mounts on to the transmission either. QUOTE(MonsterBOX @ Jun 22, 2005 - 4:30 PM) ...personally if i was doing the 3s swap i would use the 5sfe tranny...its bolt ups just fine and i havent heard of any failing yet under the power of the 3s...as for using the mr2-t [right][snapback]303004[/snapback][/right] Not true, it depends on the power you are shooting for. I've talked to XAT and the guy who is going to be doing my swap and both have told me that that 5s tranny is only good to around 250 hp. Also there are people on here who have replaced the 5s because it has failed. You are right about not swaping the tranny unless your 5s tranny is going out, it is pointless and will be just as much a hassle as swaping the motor, so why not wait. |
HaRv3sTeR tranny with 5sfe Jun 19, 2005 - 10:10 AM
kdash ok you can't use the gt-4 tranny because it... Jun 19, 2005 - 10:26 AM
HaRv3sTeR ok but this doesnt answer 100% my question
does t... Jun 19, 2005 - 11:05 AM
HaRv3sTeR bump Jun 19, 2005 - 9:56 PM
Kwanza26 Yes... but swapping in the tranny is as hard as sw... Jun 22, 2005 - 1:23 AM
Galcobar And if you're going to do the tranny swap, it... Jun 22, 2005 - 1:42 AM
Supersprynt http://www.6gc.net/forums/index.php?showtopic=2600... Jun 22, 2005 - 9:54 AM
HaRv3sTeR QUOTE(Supersprynt @ Jun 22, 2005 - 2:54 PM)ht... Jun 22, 2005 - 10:44 AM
Rjb23 QUOTE(HaRv3sTeR @ Jun 22, 2005 - 3:44 PM)QUOT... Jun 22, 2005 - 11:56 AM
Supersprynt QUOTE(MonsterBOX @ Jun 22, 2005 - 12:30 PM)ok... Jun 22, 2005 - 12:10 PM
Galcobar It's not set up exactly the same. It's set... Jun 23, 2005 - 3:43 AM
Supersprynt Minor stuff, like changing the linkage bracket and... Jun 23, 2005 - 7:45 AM![]() ![]() |
| Lo-Fi Version | Time is now: November 22nd, 2025 - 12:45 PM |