 4agze pistons ina 7afe???, will they fit? |
 Apr 21, 2005 - 3:47 PM
|
 
|
 Enthusiast  Joined Oct 10, '04 From New Jersey Currently Offline Reputation: 0 (0%)  |
I herd from a few ppl that 4agze pistons will fit in the 7afe, only thing is is that i thought the 4agze was a 1.6 and being that the 7afe is a 1.8 how would they fit?? Would the 4agze pistons be too small??
|
 |
Replies
|
Oct 29, 2005 - 1:57 AM
|
|
|
Enthusiast Joined Oct 27, '05 Currently Offline Reputation: 0 (0%) |
bro's,
so may i assume that if i wanna build a high comp NA engine on 7aGE, which piston should i go for? |
Posts in this topic
StreetRacing10PSI 4agze pistons ina 7afe??? Apr 21, 2005 - 3:47 PM
nik QUOTE(StreetRacing10PSI @ Apr 21, 2005 - 1:47... Apr 21, 2005 - 4:03 PM StreetRacing10PSI ok thanks, thats exactly what i needed to know. il... Apr 21, 2005 - 4:07 PM
nik QUOTE(StreetRacing10PSI @ Apr 21, 2005 - 2:07... Apr 21, 2005 - 4:11 PM doGGy Ehm.... from 9.5 till 10.8 on stock bore to be exa... Apr 21, 2005 - 4:15 PM nik QUOTE(doGGy @ Apr 21, 2005 - 2:15 PM)Ehm.... ... Apr 21, 2005 - 4:25 PM Hanyo have we figured out how to connect the 4a pistions... Apr 21, 2005 - 6:59 PM Kwanza26 QUOTE(Hanyo @ Apr 21, 2005 - 11:59 PM)have we... Apr 22, 2005 - 2:00 AM Hanyo so basically take the rod to a machine shop. and t... Apr 22, 2005 - 8:19 AM playr158 ok we have rods covered
but where do we find the... Apr 22, 2005 - 10:01 AM nik QUOTE(playr158 @ Apr 22, 2005 - 8:01 AM)ok we... Apr 22, 2005 - 10:31 AM playr158 7afe Apr 22, 2005 - 10:40 AM nik QUOTE(playr158 @ Apr 22, 2005 - 8:40 AM)7afe
... Apr 22, 2005 - 11:04 AM playr158 just stick with new stock valves then Apr 22, 2005 - 11:15 AM nik QUOTE(playr158 @ Apr 22, 2005 - 9:15 AM)just ... Apr 22, 2005 - 11:20 AM playr158 yea i really don't tend to change the size jus... Apr 22, 2005 - 12:29 PM nik QUOTE(playr158 @ Apr 22, 2005 - 10:29 AM)yea ... Apr 22, 2005 - 12:39 PM playr158 well if you told me nik i would have gone in on r... Apr 22, 2005 - 5:24 PM StreetRacing10PSI Yea, I am looking at new rods too. I think I am go... Apr 22, 2005 - 9:26 PM Dr_Tweak Using 4AGZE pistons in a 7AFE will give you 11:1 c... Apr 23, 2005 - 4:06 AM nik QUOTE(raven_101 @ Apr 23, 2005 - 2:06 AM)Usin... Apr 23, 2005 - 6:49 PM playr158 you pulled those numbers from where? Apr 23, 2005 - 10:05 AM playr158 exactly ^^ Apr 23, 2005 - 6:51 PM Dr_Tweak The difference in compression between the two engi... Apr 23, 2005 - 11:14 PM doGGy WRONG.
The diffetrence is not only in heads, the ... Apr 24, 2005 - 2:15 PM Dr_Tweak QUOTE(doGGy @ Apr 24, 2005 - 7:15 PM)WRONG.
... Apr 24, 2005 - 3:36 PM doGGy here im talking about 7AFE with GZE pistons. Not t... Apr 24, 2005 - 3:39 PM Kwanza26 QUOTE(raven_101 @ Apr 24, 2005 - 8:36 PM)Thin... Apr 24, 2005 - 7:33 PM playr158 ok basically all we need to know is
4agze pistons... Apr 24, 2005 - 9:07 PM StreetRacing10PSI all i really wanna know is what do i have to do to... Apr 24, 2005 - 9:14 PM Kwanza26 It'll raise your compression to higher than st... Apr 24, 2005 - 9:47 PM StreetRacing10PSI ok, so i get my turbo probly some time this week o... Apr 24, 2005 - 9:52 PM playr158 you can boost a 10:1 cr fine at 10-15psi you just ... Apr 24, 2005 - 9:57 PM Kwanza26 QUOTE(playr158 @ Apr 25, 2005 - 2:57 AM)you c... Apr 25, 2005 - 2:39 AM nik QUOTE(playr158 @ Apr 24, 2005 - 7:57 PM)you c... Apr 28, 2005 - 10:44 AM StreetRacing10PSI i no, i posted a pic in the off topic forum i thin... Apr 24, 2005 - 10:16 PM Dr_Tweak The answer to your question is in this thread. But... Apr 25, 2005 - 3:03 AM playr158 well then thank you for the piston link
i knew goi... Apr 25, 2005 - 7:18 AM playr158 oh and just so we get the line down
i refuse to sw... Apr 25, 2005 - 7:20 AM nik QUOTE(playr158 @ Apr 25, 2005 - 5:20 AM)oh an... Apr 28, 2005 - 10:46 AM playr158 well then i better make sure i have an aluminum ra... Apr 28, 2005 - 2:30 PM nik QUOTE(playr158 @ Apr 28, 2005 - 12:30 PM)well... Apr 28, 2005 - 2:35 PM playr158 i'm not a big fan of half rads i'd rather ... Apr 28, 2005 - 2:44 PM nik QUOTE(playr158 @ Apr 28, 2005 - 12:44 PM)i... Apr 28, 2005 - 3:08 PM playr158 i would say that the invader front we're both ... Apr 28, 2005 - 6:26 PM nik QUOTE(playr158 @ Apr 28, 2005 - 4:26 PM)i wou... May 2, 2005 - 9:07 AM 94ST2 OK I read through the post and we have seemed to h... Apr 28, 2005 - 11:14 PM playr158 already been convered
you have two options
low ... Apr 29, 2005 - 8:36 AM 94ST2 How much would the pistons and rods run? May 1, 2005 - 11:40 PM Kwanza26 QUOTE(94ST2 @ May 2, 2005 - 4:40 AM)How much ... May 2, 2005 - 12:23 AM 94ST2 Yeah I was figuring around that much thanks. May 2, 2005 - 12:28 AM playr158 QUOTE(nik @ May 2, 2005 - 9:07 AM)QUOTE(playr... May 2, 2005 - 11:06 AM nik i just want it to look clean and not have 4' o... May 2, 2005 - 11:50 AM playr158 well you shouldnt see most of the hose since it wi... May 2, 2005 - 12:36 PM playr158 7age? your doing a head swap or a 7afe?
if your b... Oct 29, 2005 - 2:07 AM normality78 Tks dude.
Well engine has been open apart to chec... Oct 29, 2005 - 11:30 PM playr158 cause its an econobox head Oct 30, 2005 - 2:59 PM doGGy K, time to write it again.
As i know for now im t... Oct 30, 2005 - 3:35 PM Dr_Tweak QUOTE(doGGy @ Oct 30, 2005 - 8:35 PM)K, time ... Oct 30, 2005 - 11:32 PM doGGy CR ratio was CONFIRMED like 10 times already, but ... Oct 31, 2005 - 3:17 AM nik I'M WITH DOGGY on this one it has been covered... Oct 31, 2005 - 3:52 PM Dr_Tweak Well sorry I asked, but every single time I tell p... Nov 1, 2005 - 12:48 AM nik QUOTE(Dr_Tweak @ Oct 31, 2005 - 10:48 PM)Well... Nov 1, 2005 - 10:57 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: July 12th, 2025 - 11:48 AM |