May 6, 2006 - 6:31 PM
|
|
|
Enthusiast ![]() ![]() ![]() ![]() ![]() Joined Mar 3, '04 From Hollywood, MD Currently Offline Reputation: 6 (100%) |
ok guys, i consider my swap FINISHED now because i just drove it around the block, however there are some minor problems i noticed during the test drive
first it idled about 1800 rpms, then after driving it it jumped up to 3000 my boost gauge reads 20 vac at idle so i assume no vacuum leaks my power steering doesnt work, this confuses me because everything is hooked up its hard to get it into gear, in fact when i first started it it would not go into gear, then it ended up going into reverse with some force (no grinding though) the car would lurch forward when trying to go into first and reverse when trying to go into reverse. my friend told me to re-bleed the clutch but before i went to do that i went for one more try and it finally went in, the shifting seems to get smoother the more i play with it so maybe it has something to do with the tranny being sitting bone dry for the past few months? at idle my motor shakes a bit, and by a bit i mean that even with my not so vast experience with cars i know it should not do this. btw tomorrow i will have pics and vids of everything, and ill start a before and after thread! edit: jeff, how do you drive withot power steering man, i could hardly reverse into the driveway! This post has been edited by brianforster: May 6, 2006 - 6:34 PM |
![]() |
May 7, 2006 - 12:25 AM
|
|
![]() Enthusiast ![]() ![]() ![]() ![]() ![]() Joined Nov 12, '02 From Webster Ma. Currently Offline Reputation: 1 (100%) |
congrats man!
-------------------- |
brianforster swap officially finished! (but still has minor probs) May 6, 2006 - 6:31 PM
playr158 make sure your powersteering lines are in the righ... May 6, 2006 - 7:49 PM
brianforster power steering is a leak in the high pressure line... May 6, 2006 - 7:57 PM
brianforster update: on a cold start it idles at about 2000 the... May 6, 2006 - 9:04 PM
lagos hey...noticed you called... i was out and didnt ha... May 6, 2006 - 9:20 PM
brianforster front and rear mounts are new though and those are... May 6, 2006 - 9:35 PM
lagos if they are new, then they should be ok. get a v... May 6, 2006 - 9:38 PM
brianforster also i found out the st radiator does not have a c... May 6, 2006 - 9:46 PM
bigal004321 Nice job with the swap,,and congrats on the first ... May 6, 2006 - 9:50 PM
lagos QUOTE(brianforster @ May 6, 2006 - 10... May 6, 2006 - 9:53 PM
defgeph Congrats man. You get used to no power steering.
... May 6, 2006 - 11:38 PM
CelicaZR Congrat man
You've definitely come a long wa... May 7, 2006 - 3:28 AM
brianforster well today i put better gas in it and got some vid... May 7, 2006 - 3:09 PM
Chanh55 QUOTE(brianforster @ May 7, 2006 - 1... May 7, 2006 - 3:25 PM
brianforster can someone get me a pic of this screw? because on... May 7, 2006 - 3:40 PM
Chanh55 QUOTE(brianforster @ May 7, 2006 - 1... May 7, 2006 - 3:49 PM
brianforster also with the hood down after like 5 min of runnin... May 7, 2006 - 3:44 PM
bojangles_8686 Ok here are the pics and videos from today....
... May 7, 2006 - 5:20 PM
jcbass7 not sure if this would be true, but maybe the hood... May 7, 2006 - 5:52 PM
Hanyo did you cover that hole on your down pipe?
Is your... May 7, 2006 - 6:32 PM
jcbass7 oh yea hanyo has a good point. If that hole isn... May 7, 2006 - 6:49 PM
playr158 didn't i say you needed to close that o2 senso... May 7, 2006 - 7:41 PM
BBoYRuGGeD congrats on the swap man! hope you get all... May 7, 2006 - 7:56 PM
lagos QUOTEit gets hottest right over the tubular manifo... May 7, 2006 - 7:58 PM
LewFX ill compress the vid May 7, 2006 - 8:19 PM
brianforster if you notice both of the studs are broken on that... May 7, 2006 - 9:40 PM
lagos you can keep it where it is and wrap it with exhau... May 8, 2006 - 12:24 AM
f1yen [font=Tahoma]so is your car still idling high?, be... May 9, 2006 - 9:29 PM
playr158 QUOTE(f1yen @ May 9, 2006 - 10:29 PM... May 10, 2006 - 12:32 AM
brianforster plus 2nd gen engine will not run without the AFM i... May 10, 2006 - 11:04 AM
easternpiro1 good job bryan!! im glad everything worked... May 10, 2006 - 12:43 PM
brianforster it ended up being the throttle cable was too tight... May 12, 2006 - 7:47 PM
morbiddelusions lookin good May 12, 2006 - 10:02 PM
lagos the temp gauge should sit around the middle when w... May 12, 2006 - 10:19 PM
brianforster what needs to be replaced the gauge or the thermos... May 13, 2006 - 12:18 AM
lagos QUOTE(brianforster @ May 13, 2006 - 1... May 13, 2006 - 12:57 AM
brianforster how long should it take to reach the center? May 13, 2006 - 9:08 AM
Rjb23 Depends when I first did my swap it took for ever ... May 13, 2006 - 12:31 PM
BBoYRuGGeD ^^^ yap same...about 5 min or less with mine on a ... May 13, 2006 - 2:01 PM
DG_Performance i highly recomend the trd lower thermostat for bet... May 15, 2006 - 8:17 AM![]() ![]() |
| Lo-Fi Version | Time is now: December 6th, 2025 - 5:23 PM |