Aug 14, 2007 - 1:56 AM
|
|
|
Enthusiast ![]() ![]() ![]() ![]() ![]() Joined May 12, '06 From Wilmington, NC Currently Offline Reputation: 45 (100%) |
so basically I've got a pretty bad oil leak that I'm 90% sure is from the rear main seal. so I'm going to be replacing that sometime, like this weekend maybe. I was wondering if anybody could give me some general directions on how to remove the (manual) transmission as I've never done it before. also, are there any other seals or gaskets I need to replace while I do this, or are there any things that are recommended I do while this is out?
-------------------- ![]() 94 GT - Sold -------- 69 Pontiac Lemans - Sold 88 Alltrac - Sold ---- 04 WRX - Sold 00 GT-S - Sold ------ 91 Miata - project/drift car 95 GT - Sold -------- 96 GT - New Daily Drive |
![]() |
Aug 19, 2007 - 11:32 AM
|
|
|
Enthusiast ![]() Joined Nov 10, '06 From Cleveland Currently Offline Reputation: 0 (0%) |
Are you completely sure that the rear seal is leaking? I only ask because it is uncommon for the rear seal to leak on a Toyota unless you have a ton of miles, and you are really getting into a big job where it is easy to screw a bunch of expensive stuff up. If you are sure that it is the rear seal, the first thing I would do is find a service manual for the car (most libraries have them) and read through the procedure for removing the transmission and replacing the seal. Make sure you have all the special tools that will be required. The manual will give you general directions; if you have any specific questions, I'm sure people here can answer them.
|
6strngs Rear main seal replacement Aug 14, 2007 - 1:56 AM
soulshadow Take out the motor and tranny together. Its much e... Aug 14, 2007 - 10:40 PM
6strngs I don't have the tools to remove the motor, an... Aug 15, 2007 - 12:28 AM
6strngs come on, nobody has anything to say?
right now, I... Aug 17, 2007 - 10:09 AM
6strngs can anybody tell me how to take the driver's s... Aug 18, 2007 - 11:38 PM
lagos QUOTE(6strngs @ Aug 19, 2007 - 12:38... Aug 19, 2007 - 11:47 AM
WannabeGT4 If you don't have a CV shaft puller I found th... Aug 19, 2007 - 12:41 PM
6strngs well, I got it out. I went out and searched for a ... Aug 19, 2007 - 3:31 PM
WannabeGT4 There are two U shaped clips holding the cables in... Aug 19, 2007 - 5:01 PM
6strngs QUOTE(WannabeGT4 @ Aug 19, 2007 - 3... Aug 19, 2007 - 5:07 PM
WannabeGT4 Hit 'em with a hammer, pry on them with a scre... Aug 19, 2007 - 5:13 PM
6strngs yeah, I got them. I actually did follow your advis... Aug 19, 2007 - 9:16 PM
CaliJeff QUOTE(6strngs @ Aug 19, 2007 - 7:16 ... Aug 19, 2007 - 9:22 PM
soulshadow so.......what are you supporting the motor with wh... Aug 21, 2007 - 11:13 PM
6strngs I've got one jack under the motor, one transmi... Aug 22, 2007 - 2:30 AM
6strngs that's weight reduction... right?
and in cas... Aug 26, 2007 - 11:52 AM
6strngs three full weeks? have I really been doing this 3 ... Sep 3, 2007 - 2:15 AM
lubu good work bud, good to see that car is up and runn... Sep 3, 2007 - 2:30 PM
6strngs yeah, I could only lift the transmission high enou... Sep 3, 2007 - 11:45 PM
soulshadow Awesome JOB! Good Work! Sep 12, 2007 - 11:46 AM![]() ![]() |
| Lo-Fi Version | Time is now: February 28th, 2026 - 1:01 PM |