 Rear main seal replacement, any how-to's on how to remove a transmission? |
 Aug 14, 2007 - 1:56 AM
|
 
|
 Enthusiast  Joined May 12, '06 From Wilmington, NC Currently Offline Reputation: 45 (100%)  |
so basically I've got a pretty bad oil leak that I'm 90% sure is from the rear main seal. so I'm going to be replacing that sometime, like this weekend maybe. I was wondering if anybody could give me some general directions on how to remove the (manual) transmission as I've never done it before. also, are there any other seals or gaskets I need to replace while I do this, or are there any things that are recommended I do while this is out?
--------------------  94 GT - Sold -------- 69 Pontiac Lemans - Sold 88 Alltrac - Sold ---- 04 WRX - Sold 00 GT-S - Sold ------ 91 Miata - project/drift car 95 GT - Sold -------- 96 GT - New Daily Drive |
 |
Replies
|
Aug 21, 2007 - 11:13 PM
|
|
 Enthusiast Joined Apr 18, '05 From Lincoln, Ar Currently Offline Reputation: 7 (100%) |
so.......what are you supporting the motor with while you work on the tranny.
I hope u at least have a piece of wood wrapped in chain going across your engine bay holding up the motor while your mounts are loose.... If not.... Dude, go to Wal-Mart buy an Air Compressor, tools and do the project. THEN when your done, RETURN them and say you really didn't need them. Saved myself tons of times. |
Posts in this topic
6strngs Rear main seal replacement Aug 14, 2007 - 1:56 AM
soulshadow Take out the motor and tranny together. Its much e... Aug 14, 2007 - 10:40 PM 6strngs I don't have the tools to remove the motor, an... Aug 15, 2007 - 12:28 AM 6strngs come on, nobody has anything to say?
right now, I... Aug 17, 2007 - 10:09 AM 6strngs can anybody tell me how to take the driver's s... Aug 18, 2007 - 11:38 PM jc47 Are you completely sure that the rear seal is leak... Aug 19, 2007 - 11:32 AM lagos QUOTE(6strngs @ Aug 19, 2007 - 12:38... Aug 19, 2007 - 11:47 AM WannabeGT4 If you don't have a CV shaft puller I found th... Aug 19, 2007 - 12:41 PM 6strngs well, I got it out. I went out and searched for a ... Aug 19, 2007 - 3:31 PM WannabeGT4 There are two U shaped clips holding the cables in... Aug 19, 2007 - 5:01 PM
6strngs QUOTE(WannabeGT4 @ Aug 19, 2007 - 3... Aug 19, 2007 - 5:07 PM WannabeGT4 Hit 'em with a hammer, pry on them with a scre... Aug 19, 2007 - 5:13 PM 6strngs yeah, I got them. I actually did follow your advis... Aug 19, 2007 - 9:16 PM CaliJeff QUOTE(6strngs @ Aug 19, 2007 - 7:16 ... Aug 19, 2007 - 9:22 PM 6strngs I've got one jack under the motor, one transmi... Aug 22, 2007 - 2:30 AM 6strngs that's weight reduction... right?
and in cas... Aug 26, 2007 - 11:52 AM 6strngs three full weeks? have I really been doing this 3 ... Sep 3, 2007 - 2:15 AM lubu good work bud, good to see that car is up and runn... Sep 3, 2007 - 2:30 PM 6strngs yeah, I could only lift the transmission high enou... Sep 3, 2007 - 11:45 PM soulshadow Awesome JOB! Good Work! Sep 12, 2007 - 11:46 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: February 28th, 2026 - 1:00 PM |