 GT -> GT4 rear end the same? |
 Dec 10, 2008 - 11:02 PM
|
 
|
|
Enthusiast  Joined Jul 23, '08 From Hawaii Currently Offline Reputation: 6 (100%)  |
in regards to the conversion, is the GT4 rear axle/suspension the same setup as the GT's?
mostly wondering if the rear subframe is the same or not. |
 |
Replies
|
Dec 11, 2008 - 9:31 PM
|
|
 Enthusiast Joined Dec 15, '02 From Tasmania(Australia) Currently Offline Reputation: 0 (0%) |
comming from all your gtfour experience pressure?
they have extra bracing around the strut tower, top and bottom. the whole floorpan is different. I doubt highly there would be enough room under the poverty pack floor to accomodate the subframe/diff etc . Might have to cut the floor out and weld it in a higher position. Someone on here has done it so they should be able to point you in the right direction. Obviously the floor is part of the car/welded in, but the subframes are welded in. seriously just do it properly and get a four. They came out in lhd, much less dodgy. EDIT: ill just add that ive only ever delt with Group A Rallye (mine) and a couple of imported WRC that i have worked on, but all of these have extra bracing then the poverty pack ST204's here, prehaps the non wrc/group a 205's dont have the bracing but i seriously doubt it. This post has been edited by Cuts_the_Pilot: Dec 11, 2008 - 9:38 PM -------------------- ST205 Group A Rallye GT-Four, #61 of 77............600hp GT3582r
GRX133 Toyota Mark X 350s  |
|
Dec 11, 2008 - 10:18 PM
|
|
 Moderator Joined Oct 1, '02 From fall river, ma Currently Offline Reputation: 13 (100%) |
QUOTE (Cuts_the_Pilot @ Dec 11, 2008 - 9:31 PM)  comming from all your gtfour experience pressure? they have extra bracing around the strut tower, top and bottom. the whole floorpan is different. I doubt highly there would be enough room under the poverty pack floor to accomodate the subframe/diff etc . Might have to cut the floor out and weld it in a higher position. Someone on here has done it so they should be able to point you in the right direction. Obviously the floor is part of the car/welded in, but the subframes are welded in. seriously just do it properly and get a four. They came out in lhd, much less dodgy. EDIT: ill just add that ive only ever delt with Group A Rallye (mine) and a couple of imported WRC that i have worked on, but all of these have extra bracing then the poverty pack ST204's here, prehaps the non wrc/group a 205's dont have the bracing but i seriously doubt it. no, from my EPC experience, which has VERY nice detailed pics..  like i said...the floorpan, basiclyfrom the back of the front seats back, and the rear lower strut towers. -------------------- Former Team 5SFTE pro member ;)
 13.6@108MPH, 5SFTE Powered |
Posts in this topic
luka GT -> GT4 rear end the same? Dec 10, 2008 - 11:02 PM
presure2 QUOTE (luka @ Dec 10, 2008 - 11:02 P... Dec 10, 2008 - 11:04 PM luka hmm...
I know the suspension is different....basi... Dec 11, 2008 - 12:00 AM Cuts_the_Pilot In short no.
there is heaps of differences. Just ... Dec 11, 2008 - 2:37 AM presure2 QUOTE also worth noting the four has extra bracing... Dec 11, 2008 - 7:40 AM luka So i'd have to go ahead and swap out the subfr... Dec 11, 2008 - 8:58 PM
 |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: July 18th, 2025 - 10:57 PM |