 clutch problem, 0-10km/h in 10 seconds!!! |
 May 20, 2009 - 8:58 AM
|
 
|
 Enthusiast  Joined Aug 3, '07 From Bellevue, Nebraska Currently Offline Reputation: 28 (100%)  |
so here's my dilemma. recently my clutch (i think, i'm sure) has been slowly going out on me. when i let off the clutch and smash the gas, i get all engine and no go, 5k rpms in first, and i'm doing 0-15k in about 10 seconds, if i don't have a hill to climb.
oh, and i just figured out today, that it's kinda like the clutch isn't seating all the way. you know what it's like when you let out just a little bit on the clutch, looking for the engine to grab, so you can creep up to the stop line, or to get a start going up a hill? well, mine's doing that when i take my foot off the clutch and my foot off the break, not even touching the accelerator. could it be that i just need to bleed my clutch line, or is my clutch just that shot? and, when i do replace the clutch and pressure plate, does the flywheel need replaced too, or only if it can't be smoothed out? thanks for the help -------------------- ~Andy
 Check out my Droid Goodies | My Flickr |
 |
Replies
|
May 20, 2009 - 9:03 AM
|
|
 Moderator Joined Oct 1, '02 From fall river, ma Currently Offline Reputation: 13 (100%) |
QUOTE (stetsonaw @ May 20, 2009 - 8:58 AM)  so here's my dilemma. recently my clutch (i think, i'm sure) has been slowly going out on me. when i let off the clutch and smash the gas, i get all engine and no go, 5k rpms in first, and i'm doing 0-15k in about 10 seconds, if i don't have a hill to climb. oh, and i just figured out today, that it's kinda like the clutch isn't seating all the way. you know what it's like when you let out just a little bit on the clutch, looking for the engine to grab, so you can creep up to the stop line, or to get a start going up a hill? well, mine's doing that when i take my foot off the clutch and my foot off the break, not even touching the accelerator. could it be that i just need to bleed my clutch line, or is my clutch just that shot? and, when i do replace the clutch and pressure plate, does the flywheel need replaced too, or only if it can't be smoothed out? thanks for the help sounds like its time for a new clutch. you can have your flywheel resurfaced. also replace the throw out bearing, and a rear main seal + gasket while its apart, you dont wanna have to pull the tranny off just to do a rear main down the road. -------------------- Former Team 5SFTE pro member ;)
 13.6@108MPH, 5SFTE Powered |
Posts in this topic
stetsonaw clutch problem May 20, 2009 - 8:58 AM
trdproven if you have never replaced your clutch until now, ... May 20, 2009 - 9:23 AM stetsonaw manny, what is this seal you speak of? i'm go... May 21, 2009 - 6:53 AM njccmd2002 this is it..
two ways of doing it. you can do it... May 21, 2009 - 9:36 AM stetsonaw that's a seal and two gaskets i don't have... May 21, 2009 - 10:13 AM
njccmd2002 if your car is
ST202-BLMZF 08/1995 - 07/1999 ST2... May 21, 2009 - 11:23 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 20th, 2025 - 5:11 PM |