 Greddy Profec B Spec-II settings |
 Jun 1, 2009 - 10:58 PM
|
 
|
 Enthusiast  Joined Mar 11, '09 From Baltimore, Maryland Currently Offline Reputation: 1 (100%)  |
I just installed a Greddy Profec B Spec-II
 I need some help tuning the new toy. I have a 3s-gte so 12psi is the max I should run.10psi= 68kPa 11psi= 75kPa 12psi= 82kPa 13psi= 89kPa Boost Mode Lo Set 38% Gain 10% Start Boost 0.65 (x100kPa) (range:0~3.0 x x100kPa) Warning 0.75 (x100kPa) Limiter L.20% Boost Mode Hi Set 42% Gain 15% Start Boost 0.75 (x100kPa) Warning 0.82 (x100kPa) Limiter L.30% I'm not sure about any of the settings. Are there any stickys on this? This post has been edited by speed-CCNP: Jun 1, 2009 - 10:59 PM |
 |
Replies
|
Jun 3, 2009 - 9:17 PM
|
|
 Enthusiast Joined Aug 31, '02 From Philadelphia, PA Currently Offline Reputation: 8 (100%) |
You will blow your motor if you keep that air to air top mount. Right now, you have ZERO intercooling on your car. install the front mount asap.
When you install a boost controller, you have to make sure you disconnect and cap the second port on the wastegate actuator that goes to the Turbo vsv. -------------------- 15PSI - 30MPG - Megasquirt Tuned
|
|
Jun 3, 2009 - 10:12 PM
|
|
|
Enthusiast Joined Mar 11, '09 From Baltimore, Maryland Currently Offline Reputation: 1 (100%) |
 don't want to kill the motor!!!where is the the second port on the wastegate actuator that goes to the Turbo vsv.? do you have a picture? thanks |
Posts in this topic
speed-CCNP Greddy Profec B Spec-II settings Jun 1, 2009 - 10:58 PM
lagos Every car is different, but here is the basic idea... Jun 1, 2009 - 11:24 PM
speed-CCNP Thanks, I think i got it. But 1.0 bar is equal to ... Jun 2, 2009 - 6:44 PM lagos No thats not too much boost, as long as you have a... Jun 2, 2009 - 7:00 PM speed-CCNP I still have the stock top mount IC on the car. I... Jun 3, 2009 - 9:10 PM Defgeph I have been trying to figure out how to properly s... Jun 3, 2009 - 10:25 PM presure2 QUOTE (Defgeph @ Jun 3, 2009 - 10:25... Jun 4, 2009 - 5:56 AM Defgeph QUOTE (presure2 @ Jun 4, 2009 - 6:56... Jun 4, 2009 - 11:30 AM presure2 RE: Greddy Profec B Spec-II settings Jun 4, 2009 - 11:36 AM Defgeph FU Jun 4, 2009 - 11:41 AM DEATH I gotta get me one of these toys
OP - Art is rig... Jun 4, 2009 - 3:24 PM speed-CCNP Thanks. I plan to put the FMIC on tomorrow. Jun 6, 2009 - 8:44 PM speed-CCNP i plan to use the clamps but I was told I should h... Jun 6, 2009 - 9:14 PM lagos QUOTE (speed-CCNP @ Jun 6, 2009 - 1... Jun 6, 2009 - 11:17 PM presure2 welding most of the pipes is best, but you will st... Jun 7, 2009 - 8:08 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: August 26th, 2025 - 8:55 AM |