 Intake questions-, how far, and sensor questions |
 Jun 15, 2010 - 8:33 PM
|
 
|
 Enthusiast  Joined Mar 16, '09 From New York Currently Offline Reputation: 23 (100%)  |
▼New Questions▼
I have a CAI for my ST, I feel like it gave me a little more power over stock, but it used to hang down on the tranni, and the heat shield use to actually get a little hot, and I assume the air isn't all that cold. So I moved the piping around and got a little more to bend further. I got it almost to the driver side turn signal. With the invader kit, its a big opening under the turn, and thats right about where it rests. I dont feel much of a difference from when it was in it original place and now, although it sounds better  . I was wondering, do you loose power if you go too far with the CAI piping?thanks- Also My air intake sensor (temp sensor?) is wrapped like 75% in electrical tape, never noticed it before. But should I take it off? would this affect anything? ▼Cleaning Air filter question ▼ I know there are K&N cleaner kits.... but I dont think its worth the money to buy since its not really dirty. I have a pressure washer, so I was wondering can I just lightly wash it, would that get the dirt and particles out? thanks!
This post has been edited by mgnt232: Jun 16, 2010 - 11:39 AM -------------------- I've spilt my heart into this car :) And I don't ever plan to stop  - 6GC for Life - >Semper Fi< 1994 Cupra :p 3sgte 1995 Celica ST DD 1969 Chevelle SS alllll balls. P2 approved! |
 |
Replies
|
Jun 16, 2010 - 1:47 PM
|
|
 Enthusiast Joined Mar 22, '07 From Houston, TX Currently Offline Reputation: 4 (100%) |
its not the length, its the number and the angle of bends
-------------------- QUOTE "And, as always, your friendship, help, and dedication to the advancement of Texas Celica dominance is GREATLY appreciated. Thanks bro." -DEATH 1994 GT: V6 swap, 5speed E53 W/ LSD, All Power, now RED 1995 ST: SOLD @273k miles, Auto, all power, CarPC, White 1994 ST: Totaled, 5spd, all power, Red RIP 07/09/09 @ 241,810 1994 Lexus LS400: This is my new DD |
|
Jun 16, 2010 - 2:52 PM
|
|
|
Enthusiast Joined Mar 16, '09 From New York Currently Offline Reputation: 23 (100%) |
Well heres a pic of what it basically is (pic with all but one piece of pipe)
At the end you can see the heat shield. It doesnt bend any more, just goes a little further (about 6-8") and then the filter and heat shield now. 
-------------------- I've spilt my heart into this car :) And I don't ever plan to stop - 6GC for Life - >Semper Fi< 1994 Cupra :p 3sgte 1995 Celica ST DD 1969 Chevelle SS alllll balls. P2 approved! |
Posts in this topic
mgnt232 Intake questions- Jun 15, 2010 - 8:33 PM
4-eyed-freek dawn dish soap and warm water will do, just hand w... Jun 15, 2010 - 10:33 PM Hanyo QUOTE (mgnt232 @ Jun 15, 2010 - 6:33... Jun 15, 2010 - 11:31 PM
GriffGirl QUOTE (Hanyo @ Jun 15, 2010 - 9:31 P... Jun 17, 2010 - 12:14 PM mgnt232 Bump-New Jun 16, 2010 - 12:40 PM terbear4god4life looks like 3inch piping..
i don't think the... Jun 16, 2010 - 3:52 PM mgnt232 It is 3" piping, is that too big?
There is on... Jun 16, 2010 - 4:29 PM terbear4god4life no im using 3inch too
it don't matter..i th... Jun 16, 2010 - 5:19 PM mgnt232 Cool, how do you keep your headers clean? or is th... Jun 16, 2010 - 8:55 PM hatchy_gt-s The reason your rpms increased is simple science c... Jun 16, 2010 - 10:30 PM solidxsnake QUOTE (hatchy_gt-s @ Jun 16, 2010 ... Jun 16, 2010 - 10:40 PM hatchy_gt-s QUOTE (solidxsnake @ Jun 16, 2010 - 11... Jun 16, 2010 - 10:45 PM azian_advanced QUOTE (stephen_lee @ Jun 16, 2010 - 1... Jun 17, 2010 - 12:58 AM hatchy_gt-s QUOTE (azian_advanced @ Jun 17, 2010 - 1... Jun 17, 2010 - 11:58 PM solidxsnake QUOTE (hatchy_gt-s @ Jun 18, 2010 ... Jun 25, 2010 - 10:37 AM azian_advanced QUOTE (hatchy_gt-s @ Jun 17, 2010 ... Jun 25, 2010 - 5:19 PM solidxsnake QUOTE (azian_advanced @ Jun 25, 2010 - 6... Jun 25, 2010 - 9:31 PM terbear4god4life omg my heads going too f****** explode.
it don... Jun 17, 2010 - 12:44 AM hatchy_gt-s QUOTE (terbear4god4life @ Jun 17, 2010 ... Jun 17, 2010 - 4:28 PM 95CelicaST In the end you won't gain much power, but it m... Jun 17, 2010 - 12:55 AM mgnt232 Yeah im more interested in the sound, because I li... Jun 17, 2010 - 11:27 AM 95CelicaST And NEVER wash from the outside in, or you'll ... Jun 17, 2010 - 3:03 PM terbear4god4life lol i just caught that Jun 17, 2010 - 9:05 PM chacha good stuff...surface to volume ratios...you want m... Jun 24, 2010 - 1:39 AM blu94gt Has anyone ever tried a cowl-induction intake? I... Jun 25, 2010 - 11:08 AM solidxsnake QUOTE (blu94gt @ Jun 25, 2010 - 12:0... Jun 25, 2010 - 12:13 PM blu94gt QUOTE (solidxsnake @ Jun 25, 2010 - 12... Jun 25, 2010 - 12:59 PM mgnt232 thats pretty sweet, deff. update us with anything ... Jun 25, 2010 - 11:42 PM SleekCelica You should put an intake right out the top of your... Jun 30, 2010 - 11:03 AM SwissFerdi QUOTE (SleekCelica @ Jun 30, 2010 - 12... Jun 30, 2010 - 1:44 PM solidxsnake QUOTE (SwissFerdi @ Jun 30, 2010 - 2... Jul 1, 2010 - 9:09 AM Nartanian All this talk and arguing over equations only to a... Jun 30, 2010 - 12:01 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: June 14th, 2025 - 4:36 PM |