 94-99 GT Front Wheel Bearing Measurements |
 Nov 19, 2010 - 4:00 PM
|
 
|
|
Enthusiast  Joined Feb 23, '05 From New York Currently Offline Reputation: 0 (0%)  |
has anyone ever measured the front wheel bearings? or can point me to a link with the specs? mm or inch is fine.
|
 |
Replies
|
Nov 23, 2010 - 10:00 AM
|
|
|
Enthusiast Joined Feb 23, '05 From New York Currently Offline Reputation: 0 (0%) |
Well it seems that Drive shaft shop cant make me a bearing based on the size of the wheel bearing bore being too small. So I did some searching around and found something that might work. They seated that I need something with a 1.6 bore so I checked the Integra it has a 1.6 bore but too far off, checked the MR2 turbo and still a no go, I checked the Subaru Legacy and it looks like it might just work.
When I compare the two bearings it seems that it might be a slight lose fit but the width is very close and the bore looks good enough to work. But the OD is just a tad bit smaller. 1994 TOYOTA CELICA L4 2.2L 2164CC VIN S 5SFE GT Part Number 514002 Specifications Bore (A) 1.4961 Outer Diameter (B) 2.9134 Width © 1.4173 Inner Race Radius 0.0591 Outer Race Radius 0.0591 Series FWBD 1994 SUBARU LEGACY H4 2.2L 2212CC VIN 6 BASE MODEL Part Number 517008 Specifications Bore (B) 1.6535 Outer Diameter (D) 2.8346 Width (W) 1.4961 Series 517000 1994 ACURA INTEGRA L4 1.8L 1797CC B18C1 GSR Part Number 510030 Specifications Bore (A) 1.6929 Outer Diameter (B) 3.1102 Width © 1.6142 Inner Race Radius 0.1496 Outer Race Radius 0.0023 Series FWBD Type Illustration E-3 1994 TOYOTA MR2 L4 2.0L 1998CC VIN S 3SGTE TURBO BASE MODEL Part Number 513022 Specifications Bore (A) 1.1811 Outer Diameter (B) 2.4803 Width © 1.6535 Inner Race Radius 0.1457 Outer Race Radius 0.0276 Series RWD I used this site: http://www.fme-cat.com/ This post has been edited by eazy2001x: Nov 23, 2010 - 10:01 AM |
Posts in this topic
eazy2001x 94-99 GT Front Wheel Bearing Measurements Nov 19, 2010 - 4:00 PM
Culpable04 I need a new one, and will get it tomorrow, once I... Nov 19, 2010 - 6:28 PM 99GT To build a brake setup I'd assume for his kill... Nov 19, 2010 - 9:19 PM eazy2001x not quite.. its for a custom axle setup.. i think ... Nov 22, 2010 - 8:11 AM Culpable04 I have visitors so it'll take me a few days to... Nov 22, 2010 - 8:56 AM 96stgreendemon stupid question, but how do you go about changing ... Nov 22, 2010 - 9:18 AM eazy2001x you have to remove the whole spindle then have it ... Nov 22, 2010 - 9:36 AM 96stgreendemon hmm what about some kind of bearing driver/race? Nov 22, 2010 - 9:41 AM
eazy2001x I dont understand your question. Nov 22, 2010 - 10:10 AM RocketScott I have one out in my shop that I haven't gotte... Nov 22, 2010 - 11:49 AM RocketScott Timken 514002B
OD 74.00mm
ID 38.00mm
Outer Race T... Nov 22, 2010 - 11:59 AM eazy2001x your the man.. ill forward that info over to the b... Nov 22, 2010 - 12:46 PM Culpable04 that won't work, the bearing has to be pressed... Nov 23, 2010 - 9:03 PM RocketScott The inner races of the timkin bearings i bought co... Nov 24, 2010 - 12:40 PM eazy2001x yeah.. i am looking for a company who will make cu... Nov 24, 2010 - 12:55 PM Culpable04 there is enough room to bore the knuckle to take a... Nov 24, 2010 - 6:37 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: January 12th, 2026 - 12:20 PM |