 need help finishin 3sgte install, engine started !! |
 Mar 30, 2011 - 5:58 AM
|
 
|
 Enthusiast  Joined Nov 18, '10 From montreal Currently Offline Reputation: 0 (0%)  |
i have some question, plz can someone answer it ?
those should be easy to anwser for any who did the swap so  question#1 where does this fuel line goes ?  Uploaded with ImageShack.us  Uploaded with ImageShack.us question#2 where u plug this plastic bottle (the bottom of it)  Uploaded with ImageShack.us question #3 where do i plug that line ?  Uploaded with ImageShack.us question #4 how u setup this to this to this ?? plz  Uploaded with ImageShack.us  Uploaded with ImageShack.us  Uploaded with ImageShack.us question #5 where is the plug for this (lead prestone to the chargercooler) smic)   question# 6 where does that one goes ?  Uploaded with ImageShack.us questin #7 and finally this one , i dont know where it goes ?  Uploaded with ImageShack.us question#8 where this 2 plus goes ??  Uploaded with ImageShack.us thank for any help 
This post has been edited by Needles: May 10, 2011 - 2:53 PM |
 |
Replies
|
Apr 18, 2011 - 6:03 PM
|
|
|
Enthusiast Joined Nov 18, '10 From montreal Currently Offline Reputation: 0 (0%) |
after i did a nice ground setup, 4gauge to tranny and all the way, and some other wire to ground everywhere needed,
the connector on my starter selenoid positive is loose, but is firmly tight bolted, is that normal, ? i tryed crank up the engine after my setup, but nothing, no crank only when i turn the key i heard 3 clic in the engine bay, and one clic from cpu when triyng to crank any idea ? the big smoke was the only ground wire and just overheat cause cannot hold the all the juice.. This post has been edited by Needles: Apr 18, 2011 - 6:05 PM |
Posts in this topic
Needles need help finishin 3sgte install Mar 30, 2011 - 5:58 AM
presure2 1 looks like the fuel return line
2 is an overflow... Mar 30, 2011 - 6:40 AM Needles thanks a lot presure2, im going back to work now Mar 30, 2011 - 6:52 AM presure2 looking again, #6 looks like it could be the Ic le... Mar 30, 2011 - 9:23 AM Needles ok, i have setup the water inc pump, now i will pl... Mar 30, 2011 - 9:56 AM mak5603 Glad you posted this, and glad Manny is such a 3s ... Mar 30, 2011 - 12:27 PM nsxtypeR No 3 goes directly into the intake hose between ai... Mar 30, 2011 - 12:47 PM Needles after i plugged all back in the harness and finish... Apr 4, 2011 - 8:10 PM
presure2 QUOTE (Needles @ Apr 4, 2011 - 9:10 ... Apr 10, 2011 - 10:52 AM Needles solve Apr 10, 2011 - 10:22 AM Needles now i heard clic sound when i try starting the eng... Apr 10, 2011 - 11:48 AM Needles ok interior plug done just like u do in ur progree... Apr 10, 2011 - 12:40 PM presure2 QUOTE (Needles @ Apr 10, 2011 - 1:40... Apr 10, 2011 - 5:16 PM delusionz You need to look at a GT4 build thread, those thin... Apr 10, 2011 - 5:33 PM Needles i tried to look what does go to the negative pole ... Apr 12, 2011 - 5:38 PM Needles hello again !
so im in triyng to make my ca... Apr 14, 2011 - 2:46 PM mkernz22 that wiring is a MESS! (most likely your probl... Apr 14, 2011 - 2:58 PM Needles QUOTE (mkernz22 @ Apr 14, 2011 - 2:5... Apr 14, 2011 - 3:04 PM presure2 that switch is aftermarket, prolly for some type o... Apr 14, 2011 - 5:08 PM Needles QUOTE (presure2 @ Apr 14, 2011 - 6:0... Apr 15, 2011 - 9:55 AM Defgeph Charge your battery and try again. If that doesn... Apr 14, 2011 - 7:03 PM Needles i found my mistake !! the plug for positiv... Apr 15, 2011 - 12:03 PM delusionz ????
Did you try to jump start it? The big smoke ... Apr 16, 2011 - 4:55 PM Needles yo its there lol, its extend whit orange black wir... Apr 17, 2011 - 12:37 AM delusionz Check your battery? Can you hear a click from the ... Apr 18, 2011 - 11:54 PM Needles Starter Does not Operate
When your starter does n... Apr 19, 2011 - 5:46 AM delusionz I think I can see what your problem is, I think yo... Apr 19, 2011 - 6:54 AM Needles QUOTE (delusionz @ Apr 19, 2011 - 7... May 7, 2011 - 10:29 PM Needles i had try to boost it direct on the starter and...... Apr 20, 2011 - 3:05 PM Needles omg problem solved !
my ea1 plug was bad conn... Apr 27, 2011 - 1:01 PM Needles since i dont have a clip, i dont know where the fu... Apr 27, 2011 - 2:26 PM Needles im sorry my last post a bit confusing.....
i ju... Apr 27, 2011 - 10:05 PM Needles that ok i found it
from EA1 there are 4 wires t... Apr 28, 2011 - 8:00 AM Needles its start crank over !!! wooo
whit al... May 9, 2011 - 4:12 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: December 15th, 2025 - 3:42 PM |