6G Celicas Forums

Welcome Guest ( Log In | Register )

> Car Security System Problem, "Silent Mode"
post May 21, 2011 - 12:07 PM
+Quote Post
StylnPlane



Enthusiast
*
Joined Apr 27, '11
From Grimsby, Ontario.
Currently Offline

Reputation: 0 (0%)




Hey guys, a couple days ago my alarm system went on silent, "(accident on my part).
I have the the factory security system.. i think, because it says toyota on the box underneath my seat.
Anyways the remote looks like this, https://www.keylessentryonline.com/Pics/item890_1.jpg
So..the top right button (unlock) doesnt do anything. Its the top left, which disarms, and arms the system. While unlocking,
and locking the doors.
Bottom line, I want my car to "chirp" again, when I lock it, and unlock it.
 
Start new topic
Replies
post May 28, 2011 - 1:52 AM
+Quote Post
nics



Enthusiast
*****
Joined Feb 15, '08
From Royal Oak, MI
Currently Offline

Reputation: 7 (100%)




QUOTE (StylnPlane @ May 21, 2011 - 10:07 AM) *
Hey guys, a couple days ago my alarm system went on silent, "(accident on my part).
I have the the factory security system.. i think, because it says toyota on the box underneath my seat.
Anyways the remote looks like this, https://www.keylessentryonline.com/Pics/item890_1.jpg
So..the top right button (unlock) doesnt do anything. Its the top left, which disarms, and arms the system. While unlocking,
and locking the doors.
Bottom line, I want my car to "chirp" again, when I lock it, and unlock it.


mine chirps when i turn off the car. it doesnt when i lock or unlock. this might help you

http://www.parksoffroad.com/tacomamods/ala...moteprogramming

edit:

PIEZO OPERATION MODE

One of the first things that I did was to turn off the annoying "beep" that would happen every time I locked or unlocked the truck. To turn this feature on or off, follow these directions:

The factory setting for the PIEZO operation mode is ON. When set to "OFF", only operation during REMOTE ARMING & DISARMING is affected.

1: Insert the key into the ignition and turn it to on (not acc).
2: Using one remote control, press and hold both buttons at the same time for over 2 seconds, until the status monitor's LED turns on.
***You must perform the next steps within 30 seconds***
To turn the piezo off: Press and release the bottom remote control button once. The piezo chirper chirps once, and the exterior lights flash once. Turn the ignition switch to the lock position. The piezo chirper chirps 3 times, and the exterior lights flash 3 times.

To turn the piezo on: Press and release the bottom remote control button twice. The piezo chirper chirps twice, and the exterior lights flash twice. Turn the ignition switch to the lock position. The piezo chirper chirps 3 times, and the exterior lights flash 3 times.

If you do not turn the ignition key to lock, or exceed 30 seconds during the programming steps, the status monitor's LED will turn off and the previous


This post has been edited by nics: May 28, 2011 - 1:59 AM


--------------------
God made man....
Everything else...
Made in China

post May 29, 2011 - 6:25 PM
+Quote Post
StylnPlane



Enthusiast
*
Joined Apr 27, '11
From Grimsby, Ontario.
Currently Offline

Reputation: 0 (0%)




QUOTE (nics @ May 28, 2011 - 1:52 AM) *
QUOTE (StylnPlane @ May 21, 2011 - 10:07 AM) *
Hey guys, a couple days ago my alarm system went on silent, "(accident on my part).
I have the the factory security system.. i think, because it says toyota on the box underneath my seat.
Anyways the remote looks like this, https://www.keylessentryonline.com/Pics/item890_1.jpg
So..the top right button (unlock) doesnt do anything. Its the top left, which disarms, and arms the system. While unlocking,
and locking the doors.
Bottom line, I want my car to "chirp" again, when I lock it, and unlock it.


mine chirps when i turn off the car. it doesnt when i lock or unlock. this might help you

http://www.parksoffroad.com/tacomamods/ala...moteprogramming

edit:

PIEZO OPERATION MODE

One of the first things that I did was to turn off the annoying "beep" that would happen every time I locked or unlocked the truck. To turn this feature on or off, follow these directions:

The factory setting for the PIEZO operation mode is ON. When set to "OFF", only operation during REMOTE ARMING & DISARMING is affected.

1: Insert the key into the ignition and turn it to on (not acc).
2: Using one remote control, press and hold both buttons at the same time for over 2 seconds, until the status monitor's LED turns on.
***You must perform the next steps within 30 seconds***
To turn the piezo off: Press and release the bottom remote control button once. The piezo chirper chirps once, and the exterior lights flash once. Turn the ignition switch to the lock position. The piezo chirper chirps 3 times, and the exterior lights flash 3 times.

To turn the piezo on: Press and release the bottom remote control button twice. The piezo chirper chirps twice, and the exterior lights flash twice. Turn the ignition switch to the lock position. The piezo chirper chirps 3 times, and the exterior lights flash 3 times.

If you do not turn the ignition key to lock, or exceed 30 seconds during the programming steps, the status monitor's LED will turn off and the previous


Hey thx,
But couldnt solve the problem

Posts in this topic


Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: July 24th, 2025 - 11:54 AM