 st205 amp power wire... |
 Jul 28, 2011 - 11:21 PM
|
 
|
|
Enthusiast  Joined Jul 27, '11 From calgary Currently Offline Reputation: 0 (0%)  |
for you st205 owners since the 202s probably dont have this issue, but where did you guys run the power wire to the trunk? there is absolutely nowhere that i can see to get that wire from the engine bay to the inside of the car. whats the secret? drill a new hole?
|
 |
Replies
|
Jul 29, 2011 - 10:20 PM
|
|
 Enthusiast Joined Feb 11, '08 From Auckland, New Zealand Currently Offline Reputation: 0 (0%) |
you should not need to drill anything to get a wire to front and back lol
I have a 2ga power wire , a 2ga ground wire and an ID6mm silicone tube running front to back without drilling anything, as cuts said stick it in with the rubber boot that covers the main looms on the passenger side, you bring them through, and tuck in behind the kick panel, then theres a nice place already made for wires to run under the door sill, then through the rear you can follow the fuel flap release cable if you like, or on the other side is the boot release cable you can follow which is all behind the rear panels, just pop the speaker grill off, undo the screw and the whole thing can be pryed loose ... then if you pry up the bottom of the rear seats, you have an opening to feed through to the boot,... -------------------- Mike W
1996 Toyota Celica ST205 GT-FOUR GT2860RS turbine, TiAL mvr44, JE 86.5φ piston, Clutchmasters FX400, APEX P-FC 269awhp / 273ft-lbs |
Posts in this topic
94_gt4 st205 amp power wire... Jul 28, 2011 - 11:21 PM
mkernz22 you mean the power wire for the amp that connects ... Jul 29, 2011 - 12:32 AM 94_gt4 ya thats exactly it, i knew i would have to drill,... Jul 29, 2011 - 12:41 AM mkernz22 woahh. never run something like that outside the c... Jul 29, 2011 - 2:12 AM Cuts_the_Pilot Run it through where the engine/ecu loom goes thro... Jul 29, 2011 - 5:10 AM 94_gt4 i covered it with loom and all but it must have be... Jul 29, 2011 - 9:27 AM rave2n I ran my through the left fender, there is a hole ... Jul 29, 2011 - 10:23 AM 94_gt4 ^^thats exactly what i did except there isnt a goo... Jul 29, 2011 - 11:30 AM
rave2n QUOTE (94_gt4 @ Jul 29, 2011 - 11:30... Jul 29, 2011 - 1:28 PM 94_gt4 double sided tie downs? wtf is that? lol not doubl... Jul 29, 2011 - 2:06 PM rave2n http://www.itw-fastex.com/catalog/index.ph.../c/19... Jul 29, 2011 - 2:26 PM 94_gt4 ahhhh ****! good call! thanks! Jul 29, 2011 - 3:29 PM 94_gt4 i tried doing this but i couldnt find anywhere tha... Jul 30, 2011 - 12:05 PM Cuts_the_Pilot i assume your car is rhd? Jul 30, 2011 - 8:13 PM delusionz undo the tape on the end that connects the flex ho... Jul 30, 2011 - 9:47 PM 94_gt4 yes its RHD, im still not sure which area you mean... Jul 31, 2011 - 12:50 AM Cuts_the_Pilot See the red arrows, they are pointing to where the... Jul 31, 2011 - 2:55 AM apex-86 There's a hole with a rubber grommet and a cab... Aug 6, 2011 - 11:31 PM Cuts_the_Pilot Why would you run a power cable across the engine ... Aug 7, 2011 - 12:27 AM apex-86 No particular reason, I just found it easier to ru... Aug 7, 2011 - 12:34 AM 94_gt4 so ya, cut a hole in there, man i wish i knew it w... Aug 12, 2011 - 6:42 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: July 29th, 2025 - 2:00 PM |