 How high do you guys rev your 5SFE? |
 Jan 17, 2008 - 2:38 PM
|
 
|
|
Enthusiast  Joined Feb 18, '07 From Calgary, Alberta Currently Offline Reputation: 0 (0%)  |
I am new to the 5SFE and I noticed this motor has very low end power. What range of RPM could I be reving to still keep my motor reliable? I am afriad to rev to 6k RPM because this motor has such a long stroke.
|
 |
Replies
|
Jan 11, 2012 - 9:58 AM
|
|
 Enthusiast Joined Mar 22, '07 From Houston, TX Currently Offline Reputation: 4 (100%) |
lager TB will give you...
rougher throttle response (less linear, little pedal push = most power, and very little difference after 50% throttle) loss of lower end torque as the air speed is slowed down probably not much gain in the high RPM where it flows the most air. I have faith in 90% of Toyota engineering decisions. It was probably matched to the engine for a reason. -------------------- QUOTE "And, as always, your friendship, help, and dedication to the advancement of Texas Celica dominance is GREATLY appreciated. Thanks bro." -DEATH 1994 GT: V6 swap, 5speed E53 W/ LSD, All Power, now RED 1995 ST: SOLD @273k miles, Auto, all power, CarPC, White 1994 ST: Totaled, 5spd, all power, Red RIP 07/09/09 @ 241,810 1994 Lexus LS400: This is my new DD |
Posts in this topic
Projek_01 How high do you guys rev your 5SFE? Jan 17, 2008 - 2:38 PM
808celica i take mines on reliable driviing day around 3K if... Jan 17, 2008 - 2:49 PM bccentaur3 I never go past 5,000 rpm. You don't get squat... Jan 17, 2008 - 2:53 PM
Penkka QUOTE(bccentaur3 @ Jan 17, 2008 - 2... Jan 17, 2008 - 5:54 PM 808celica lolz same here. where can i find a nice set?????? Jan 17, 2008 - 3:08 PM DEATH Headers, full exhaust and intake made a noticable ... Jan 17, 2008 - 3:15 PM bccentaur3 Then its not worth it. I would rather swap in a 3s... Jan 17, 2008 - 3:46 PM 95st-celica i'll tell you what....long story short 2 of my... Jan 17, 2008 - 5:15 PM mrgrape wait is it bad to rev ur 5sfe past 6????
cuz i usu... Jan 17, 2008 - 6:11 PM thespacepanda It's never bad to rev your engine unless you g... Jan 17, 2008 - 6:16 PM Penkka QUOTE(thespacepanda @ Jan 17, 2008 - 6... Jan 17, 2008 - 6:32 PM jason i believe from dyno sheets the best shift point is... Jan 17, 2008 - 6:21 PM thespacepanda QUOTE(jason @ Jan 17, 2008 - 11:21 P... Jan 17, 2008 - 6:34 PM GriffGirl Lately my 7A hits max torque when parked outside w... Jan 17, 2008 - 6:40 PM Penkka QUOTE(GriffGirl @ Jan 17, 2008 - 6:4... Jan 17, 2008 - 6:43 PM GriffGirl 3:49 in the afternoon here on the other side of th... Jan 17, 2008 - 6:49 PM thespacepanda Yeah, well it's almost 6pm here, and I'm a... Jan 17, 2008 - 6:51 PM GriffGirl Wacky texans! Jan 17, 2008 - 6:55 PM xs94st hmm..i drive a 7a and i dont push the overdrive in... Jan 17, 2008 - 8:42 PM aspen I usually only rev it to about 3k, but if I'm ... Jan 17, 2008 - 10:37 PM bccentaur3 Well you'd have to uninstall plenty of things ... Jan 17, 2008 - 11:20 PM Batman722 my dyno sheet compared to a stock 5s.
I can shif... Jan 18, 2008 - 12:17 AM Celicav QUOTE(Batman722 @ Jan 17, 2008 - 10... Jan 18, 2008 - 1:43 AM presure2 QUOTE(Celicav @ Jan 18, 2008 - 1:43 ... Jan 18, 2008 - 5:01 PM Kadett @Penka:
Your figures of the 3S-GE are from the 4t... Jan 18, 2008 - 6:26 AM Penkka QUOTE(Kadett @ Jan 18, 2008 - 6:26 A... Jan 18, 2008 - 7:25 AM playr158 till vtech kicks in.... Jan 18, 2008 - 8:23 AM TRD11 QUOTE i have a good theory .... if the motor can... Jan 10, 2012 - 7:54 PM Neon90424 Im thinking that would actually slow down the air.... Jan 10, 2012 - 8:17 PM dakotahwyatt QUOTE (Neon90424 @ Jan 10, 2012 - 9... Jan 10, 2012 - 8:20 PM Neon90424 only way to change the density would be lowering t... Jan 10, 2012 - 8:24 PM dakotahwyatt QUOTE (Neon90424 @ Jan 10, 2012 - 9... Jan 10, 2012 - 8:52 PM Neon90424 from what I've read having a larger throttlebo... Jan 10, 2012 - 9:22 PM dakotahwyatt QUOTE (Neon90424 @ Jan 10, 2012 - 10... Jan 10, 2012 - 9:43 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: July 25th, 2025 - 10:47 PM |