 Terrible day |
 Mar 28, 2012 - 3:25 PM
|
 
|
 Enthusiast  Joined Oct 29, '11 From Haltom City, Texas Currently Offline Reputation: 1 (100%)  |
So it all started with a flat tire yesterday, which was no big deal since I was in a GREAT mood because I figured out my dead cylinder was being caused by a valve shim(holding a valve open) and not a burnt valve, So I replaced the tire began the process of measuring the valve shims.
Upon removing the valve cover I found a mirror-on-an-extendable-stick tool sitting inside my engine, which means Im a retard and left it there last time I had the engine open. The mirror was missing(probably in a million peices inside my bearings) so I changed the oil and filter immediately(thank god the oil looked perfect, maybe it is all in the filter) Lol so then last night I dropped a feeler gauge into the engine, and it slid right down into the oil pan and is unretreivable with a magnet so I guess I will be pulling the oil pan. Oh and toyota said it will take one to one and a half weeks for the shims to come in and they do not carry the valve tool so guess I will be removing/installing cams twice, once to measure the shims to order new ones and again to install new shims. Oh and why is the FPIG $40 bucks? that seems outrageous |
 |
Replies
|
Mar 29, 2012 - 12:31 PM
|
|
|
Enthusiast Joined Oct 29, '11 From Haltom City, Texas Currently Offline Reputation: 1 (100%) |
Anybody got advice for getting the very bottom bolt out of the block/bellhousing so I can remove this reinforcement plate that covers the end of the oil pan? Im not looking forward to removing the cross-support that the mid motormounts bolt to to remove this single bolt. Can I just loosen the rear mount and undo the front mount to get enough room to pull it?
|
|
Mar 29, 2012 - 6:21 PM
|
|
 Enthusiast Joined Jan 17, '08 From JB MDL, NJ Currently Offline Reputation: 30 (100%) |
QUOTE (Special_Edy @ Mar 29, 2012 - 12:31 PM)  Anybody got advice for getting the very bottom bolt out of the block/bellhousing so I can remove this reinforcement plate that covers the end of the oil pan? Im not looking forward to removing the cross-support that the mid motormounts bolt to to remove this single bolt. Can I just loosen the rear mount and undo the front mount to get enough room to pull it? I had to remove the front crossmember bolts, remove front motor mount bolts, and loosen rear mount bolts. Then move crossmember out of way, just enough to give me clearance. |
Posts in this topic
Special_Edy Terrible day Mar 28, 2012 - 3:25 PM
Special_Edy BTW it is a 94 GT hatchback with a 5S-FE and the 5... Mar 28, 2012 - 8:43 PM mak5603 FIPG $14 from Twos R Us. Mar 28, 2012 - 8:55 PM enderswift when it rains it pours. At least you have the skil... Mar 28, 2012 - 9:14 PM Tigawoods there was a place in philly i went to where i was ... Mar 28, 2012 - 9:20 PM bmj67 Valve Tool Mar 28, 2012 - 9:33 PM
Special_Edy QUOTE (bmj67 @ Mar 28, 2012 - 9:33 P... Mar 28, 2012 - 11:55 PM Special_Edy Whoops sry my phone posted that last message twice... Mar 29, 2012 - 5:01 PM Special_Edy okay so I have the motormounts unbolted(i had to r... Mar 30, 2012 - 8:49 PM bmj67 Try backing the stud out using the 2 nut method. I... Mar 30, 2012 - 10:21 PM Special_Edy Thanks I got it out with the two nuts, and finally... Mar 30, 2012 - 11:51 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: August 21st, 2025 - 4:08 PM |