 Tools to replace wheel bearing, Are these tools necessary for replacing wheel bearing? |
 Nov 18, 2012 - 2:40 AM
|
 
|
|
Enthusiast  Joined Sep 9, '12 Currently Offline Reputation: 0 (0%)  |
Are these tools necessary for replacing wheel bearing of 6G Toyota Celica?
hub & dust cap pliers  bearing packer  bearing race punch  bearing race & seal set 
This post has been edited by dangqiwu: Nov 18, 2012 - 2:07 PM |
 |
Replies
|
Nov 22, 2012 - 10:33 AM
|
|
|
Enthusiast Joined Dec 28, '11 From GA Currently Offline Reputation: 0 (0%) |
QUOTE Labor REPLACE BOTH FRONT WHEEL BEARINGS, 60*3.5(hours)=210 WHEEL BEARINGS, $72*2=144 That labor charge includes removing the hubs, pressing out/in the bearing and reassembling the hubs. If you do the majority of the labor and just walk into the shop holding the hubs and new bearings, the labor charge just to press bearing out/in will be about $20-$30 for each side |
Posts in this topic
dangqiwu Tools to replace wheel bearing Nov 18, 2012 - 2:40 AM
azian_advanced you'll need the pliers if you intend to keep t... Nov 18, 2012 - 2:01 PM czwalga Races are kinda needed, I have axle nut sockets t... Nov 18, 2012 - 4:39 PM dangqiwu Thank @azian_advanced and @czwalga
I found no nee... Nov 18, 2012 - 6:12 PM
czwalga QUOTE (dangqiwu @ Nov 18, 2012 - 6:1... Nov 18, 2012 - 6:58 PM dangqiwu QUOTE (czwalga @ Nov 18, 2012 - 6:58... Nov 18, 2012 - 10:56 PM dangqiwu QUOTE (czwalga @ Nov 18, 2012 - 6:58... Nov 19, 2012 - 11:21 PM azian_advanced I seriously doubt it. I use my dad's 25-ton p... Nov 20, 2012 - 1:49 AM dangqiwu QUOTE (azian_advanced @ Nov 20, 2012 - 1... Nov 20, 2012 - 3:29 AM czwalga The 12 ton will probably work. I have the 20ton f... Nov 20, 2012 - 7:13 AM dangqiwu QUOTE (czwalga @ Nov 20, 2012 - 7:13... Nov 20, 2012 - 3:01 PM czwalga QUOTE (dangqiwu @ Nov 20, 2012 - 3:0... Nov 20, 2012 - 8:26 PM njccmd2002 if its the front bearing, take it to a shop.
the ... Nov 20, 2012 - 9:45 PM dangqiwu QUOTE (njccmd2002 @ Nov 20, 2012 - 10... Nov 20, 2012 - 10:10 PM mkernz22 It should be only $20 to $30, per side, ... Nov 20, 2012 - 10:20 PM dangqiwu QUOTE (mkernz22 @ Nov 20, 2012 - 11... Nov 20, 2012 - 11:23 PM mkernz22 QUOTE (dangqiwu @ Nov 20, 2012 - 11... Nov 24, 2012 - 12:10 PM ILoveMySilly97 QUOTE (mkernz22 @ Nov 24, 2012 - 9:1... Nov 24, 2012 - 2:10 PM trdproven at the most its just basic tools, and usually its ... Nov 21, 2012 - 1:26 AM soulshadow A hammer will work but you need to know what your ... Nov 22, 2012 - 12:14 AM trdproven QUOTE (soulshadow @ Nov 22, 2012 - 3... Nov 22, 2012 - 5:11 PM jordisonjr Please please PLEASE, don't use a hammer.
As s... Nov 22, 2012 - 2:08 PM ILoveMySilly97 If it's the front bearing. There's a how t... Nov 24, 2012 - 11:29 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 16th, 2025 - 7:03 PM |