 AT vs ST chassis differences? |
 Jan 6, 2013 - 2:21 PM
|
 
|
|
Enthusiast Joined Dec 13, '12 From MA Currently Offline Reputation: 0 (0%)  |
Just looking for info on the major to minor differences between a AT and ST chassis.
|
 |
Replies
|
Jan 6, 2013 - 10:41 PM
|
|
|
Enthusiast Joined Dec 13, '12 From MA Currently Offline Reputation: 0 (0%) |
Thanks for all the info, this will save me a lot of time. I had looked over the car and notice ill have to find a different gas tank or run a cell, and fab up mounts for the carrier bearing for the drive shaft. If I have a rear AWD subframe that should bolt up, correct? So next step is to find me a GT4 clip!
|
|
Jan 7, 2013 - 9:05 PM
|
|
|
Enthusiast  Joined Jan 17, '04 From Boston, MA Currently Offline Reputation: 1 (100%) |
QUOTE (Nespeed @ Jan 6, 2013 - 10:41 PM)  Thanks for all the info, this will save me a lot of time. I had looked over the car and notice ill have to find a different gas tank or run a cell, and fab up mounts for the carrier bearing for the drive shaft. If I have a rear AWD subframe that should bolt up, correct? So next step is to find me a GT4 clip! The ST205 rear floor pan is unique to the GT4. The GT4 sub frame will not bolt up directly to other models. Need to fab up mounts. I can and has been done. Not hard if you are good at welding. :-) Gas tank for an ST205 or an ST185 could be used, just hangs a bit low. Have you done a search for ST205 or AWD swaps ? There were two in the MA area. Regards; ------------------------ This post has been edited by GMan: Jan 7, 2013 - 9:07 PM |
|
Jan 7, 2013 - 9:35 PM
|
|
|
Enthusiast Joined Dec 13, '12 From MA Currently Offline Reputation: 0 (0%) |
QUOTE (GMan @ Jan 7, 2013 - 10:05 PM) QUOTE (Nespeed @ Jan 6, 2013 - 10:41 PM) Thanks for all the info, this will save me a lot of time. I had looked over the car and notice ill have to find a different gas tank or run a cell, and fab up mounts for the carrier bearing for the drive shaft. If I have a rear AWD subframe that should bolt up, correct? So next step is to find me a GT4 clip! The ST205 rear floor pan is unique to the GT4. The GT4 sub frame will not bolt up directly to other models. Need to fab up mounts. I can and has been done. Not hard if you are good at welding. :-) Gas tank for an ST205 or an ST185 could be used, just hangs a bit low. Have you done a search for ST205 or AWD swaps ? There were two in the MA area. Regards; ------------------------ Oh ok, so my only concern is messing up the geometry of the suspension if things aren't straight. I have plenty of welding hrs, are these major changes to the mount locations on the subframe? I will do some seaching, thanks. |
Posts in this topic
Nespeed AT vs ST chassis differences? Jan 6, 2013 - 2:21 PM
BonzaiCelica same!!! except sway bar thickness. but... Jan 6, 2013 - 2:59 PM Nespeed What about motor mount locations? Jan 6, 2013 - 4:45 PM RabidTRD The chassis is the same for the ST and GT.
Brake... Jan 6, 2013 - 6:43 PM
Nespeed QUOTE (RabidTRD @ Jan 6, 2013 - 6:43... Jan 6, 2013 - 7:35 PM Special_Edy AT = A series engine
ST = S series engine
The GT(... Jan 6, 2013 - 8:14 PM richee3 Edit: Never mind. Posted before reading. Jan 6, 2013 - 8:14 PM RabidTRD For the GT4 front clip there is a bar you'll n... Jan 6, 2013 - 8:15 PM Special_Edy QUOTE (RabidTRD @ Jan 6, 2013 - 9:15... Jan 6, 2013 - 8:21 PM garin motor mounts Jan 7, 2013 - 9:39 PM Special_Edy QUOTE (Nespeed @ Jan 6, 2013 - 10:41... Jan 7, 2013 - 10:24 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 9th, 2025 - 11:59 AM |