 axle install, got any tips? |
  |
 May 22, 2006 - 3:58 PM
|
 
|
|
Enthusiast  Joined Oct 6, '05 Currently Offline Reputation: 0 (0%)  |
so, im probably not a great mechanic but i was able to pull my axle , basically the snap ring wasent locked into place when my stepdad refurbished my old axle(hes a mechanic lol)... so i took matters into my own hands and removed the broken axle, tomorrow my new axle will be here... i got the putting it back in down,
my question is. any tips or things i need to do before i install the new axle? do i need to grease/lube any thing? thanks in advance Willy -------------------- Willy //2o9// California |
|
May 22, 2006 - 8:54 PM
|
|
 Enthusiast Joined Mar 31, '04 From Summerville, SC Currently Offline Reputation: 5 (100%) |
Put some grease around the part of the axle that goes into the tranny so that it doesn't damage the seal, other than that, make sure the snap ring snaps into place... and remember to refill the tranny afterwards
 Have fun. -Doc -------------------- -Dr Tweak, 6GC's resident engine swap wiring expert extraordinaire Click here to see my swaps drtweak@phoenixtuning.com |
|
May 23, 2006 - 8:20 PM
|
|
|
Enthusiast Joined Oct 6, '05 Currently Offline Reputation: 0 (0%) |
QUOTE(Dr_Tweak @ May 22, 2006 - 8:54 PM) [snapback]436838[/snapback] Put some grease around the part of the axle that goes into the tranny so that it doesn't damage the seal, other than that, make sure the snap ring snaps into place... and remember to refill the tranny afterwards Have fun. -Doc hey doc, im having some trouble getting the axle to go in, it goes in like an 8th of inch and stops, it will not go in any further its my driverside axle, im stuck ive been at this for like 5 hours, can u help me out? is their a trick to making it go in the rest of the way? -------------------- Willy //2o9// California |
|
May 23, 2006 - 9:36 PM
|
|
 Enthusiast Joined Mar 8, '04 From Newport, RI Currently Offline Reputation: 63 (99%) |
just hit it harder
 it can be tough getting it seated properly, it took a few trys and patience with mine. Just pull it back out a bit and bang that bastard in. -------------------- |
|
May 23, 2006 - 11:56 PM
|
|
 Enthusiast Joined Aug 31, '02 From Philadelphia, PA Currently Offline Reputation: 8 (100%) |
all you have to do is line it up by hand as best as you can. then you take a long flat head screw driver and a hammer and tap each side of the axel in.
-------------------- 15PSI - 30MPG - Megasquirt Tuned
|
|
May 24, 2006 - 6:43 PM
|
|
|
Enthusiast Joined Oct 6, '05 Currently Offline Reputation: 0 (0%) |
so... i installed the axle, and it popped back out on the test drive, then the lugnut bolt broke off... so im 1 lug short... i hate my car
-------------------- Willy //2o9// California |
|
May 24, 2006 - 6:57 PM
|
|
|
Enthusiast Joined Mar 11, '06 From Way South Chicago Currently Offline Reputation: 0 (0%) |
if the axle popped out then it wasnt in all the way, you'll feel it go CLACK when it snaps into place. get a brass hammer or a peice of wood and hold against the axlenut end of the axle and give it a good smack or 2 to knock it into place. i know my passenger side was difficult to snap in. if not, then try what lagos said, but try using a pry bar since it'll be longer and easier to hit.
-------------------- |
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: June 9th, 2025 - 8:20 AM |