 glo guagues. |
  |
 Jun 26, 2006 - 11:15 AM
|
 
|
|
Enthusiast  Joined Dec 9, '05 From Long Beach Currently Offline Reputation: 1 (100%)  |
ok i wana know how do you put em in, juss for research purpouses.
do you need double sided tape so that the guagues dont pop up? and what about the needles, how do you remove it and still keep it accurate? can you pop it out with a fork? This post has been edited by XS4lv1Truch0x: Jun 26, 2006 - 11:15 AM -------------------- Is this good enuff 4 ya? :D
 |
|
Jun 26, 2006 - 1:18 PM
|
|
 Enthusiast Joined Feb 22, '03 Currently Offline Reputation: 0 (0%) |
-------------------- Note to new members. Discussions such as the ones below are forbidden.
http://www.6gc.net/forums/index.php?showtopic=26310&hl= |
|
Jun 26, 2006 - 1:38 PM
|
|
|
Enthusiast Joined Dec 9, '05 From Long Beach Currently Offline Reputation: 1 (100%) |
i already read that but im asking about the needles and how to keep them accurate.
This post has been edited by XS4lv1Truch0x: Jun 26, 2006 - 1:38 PM -------------------- Is this good enuff 4 ya? :D
|
|
Jun 26, 2006 - 1:44 PM
|
|
 Enthusiast Joined Aug 31, '02 From Philadelphia, PA Currently Offline Reputation: 8 (100%) |
DO NOT REMOVE THE NEEDLES
-------------------- 15PSI - 30MPG - Megasquirt Tuned
|
|
Jun 26, 2006 - 2:14 PM
|
|
|
Enthusiast Joined Dec 9, '05 From Long Beach Currently Offline Reputation: 1 (100%) |
for research purpouses! read the thing throughly.
can you move the needles just enough so that you can slide the guagues in? -------------------- Is this good enuff 4 ya? :D
|
|
Jun 26, 2006 - 10:50 PM
|
|
 Enthusiast Joined Aug 17, '03 From Bloomington, Indiana Currently Offline Reputation: 62 (98%) |
QUOTE(lagos @ Jun 26, 2006 - 2:44 PM) [snapback]449092[/snapback] DO NOT REMOVE THE NEEDLES well said... i did remove them and im up a creek with no paddle --------------------  |
|
Jun 27, 2006 - 2:06 AM
|
|
|
Enthusiast Joined Dec 9, '05 From Long Beach Currently Offline Reputation: 1 (100%) |
so if you guys didnt remove the needles, how did you put the guagues in keeping the speedo and other guagues accurate?
-------------------- Is this good enuff 4 ya? :D
|
|
Jun 27, 2006 - 2:29 AM
|
|
 Enthusiast Joined Jun 16, '06 From Bowling Green KY Currently Offline Reputation: 7 (100%) |
take like a small flat head screw drive and slide it in that little gap on the backside of the needle and pry up very carefully... i ended up taking mine all the way off and i'm 5mph off now... ugh, the tach works and i ended up breaking my damn fuel gauge thing, oh well. just be careful man
-------------------- **If you play My Brute, joing the 6gc.net clan!**
--A section of a kid's actual test that had been scanned--  |
|
Jun 27, 2006 - 2:42 AM
|
|
 Enthusiast Joined Feb 3, '06 From Czech Republic (Europe) Currently Offline Reputation: 56 (100%) |
QUOTE(XS4lv1Truch0x @ Jun 26, 2006 - 9:14 PM) [snapback]449107[/snapback] for research purpouses! read the thing throughly. can you move the needles just enough so that you can slide the guagues in? That's right! I have them too (see) and no problem with needles during instalation at all... -------------------- No more replicas... This is evolution... This is SS-four :)
 ________[Featured Celica of 6gc.net @ 2010]_________ |
|
Jun 27, 2006 - 3:35 PM
|
|
|
Enthusiast Joined Dec 9, '05 From Long Beach Currently Offline Reputation: 1 (100%) |
okay, in the event if i ever mess up with the gas guague or the temp guague, cant i top theh gass off and place the needle on the F
or on the temp guague, cant i put it sticking in the middle while the car is operating and warmed up, wont it work the same? -------------------- Is this good enuff 4 ya? :D
|
|
Jun 27, 2006 - 4:21 PM
|
|
 Enthusiast Joined Jun 19, '05 From Nebraska Currently Offline Reputation: 4 (100%) |
I installed them in the old celica and my current celica by taking off the needles and both times i had no problems with all gauges remaning 100% accurate. But that is a rarity. Trust me. Just have to be very delicate.
-------------------- Teh Celica sleeps for Winter '06. Suspension overhaul begins........
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: July 18th, 2025 - 12:20 AM |