 FS ST205 Calipers, Rotors, front ABS hubs, pads $700 shipped USA, Pics inside |
  |
 Mar 13, 2009 - 7:49 PM
|
 
|
 Enthusiast  Joined Mar 13, '09 From ATX Currently Offline Reputation: 0 (0%)  |
I'm new here but have been on Alltrac.net for a while. I also know darthripley here on your site if you need references.
I'm in Austin, TX and have a 93 ST-185 (All-Trac). I just bought these in February but I have had zero time to put them on or finish the adjustments needed to make them fit on my st185. I figured these might be of interest over here... I have the front ST-205 ABS hubs with the dust shields, All four calipers with semi used pads, all of the hardware, and all 4 rotors. You can have it all for $700 shipped FedEx in the Lower 48. I bought some rust off stuff for the hubs and only soaked one of the front rotors, that stuff works really well, if you want to clean the rotors up more. I also degreased and scrubbed down the calipers. I started stripping the old red paint off and only got one rear one done so far. I need to address my dripping rear diff and get a new charge cooler - it's more pressing right now than the brakes. These are in good shape and there is good life left on the pads and rotors. They also have 2 uncut lines! Nice to meet everyone, I'll post up my car and more info next. Pics:   Hardware:  More pics here: Pics of Hubs more pics http://s369.photobucket.com/albums/oo139/alltrac93/calipers/ |
|
Mar 15, 2009 - 2:31 PM
|
|
|
Enthusiast Joined Mar 13, '09 From ATX Currently Offline Reputation: 0 (0%) |
|
|
Mar 15, 2009 - 8:30 PM
|
|
|
Enthusiast Joined Apr 23, '08 From boston MA Currently Offline Reputation: 5 (100%) |
can you show me measurement of the rotors right now? with a micrometer?
|
|
Mar 15, 2009 - 10:45 PM
|
|
|
Enthusiast Joined Mar 13, '09 From ATX Currently Offline Reputation: 0 (0%) |
I don't have a micrometer but I'll pick one up tomorrow and get some measurements. I could use one....
|
|
Mar 16, 2009 - 12:24 AM
|
|
 Enthusiast Joined Apr 19, '07 From Dayton, Ohio Currently Offline Reputation: 7 (100%) |
dibs!!!! im serious! can it be bought directly from you so i dont ahve to mess with ebay?
-------------------- poopra sellout... 88targa, 50trim ct, 383lsd, and shreadin tires like its my job!!!
 QUOTE (RUNNIN-LOW @ Feb 17, 2009 - 1:53 PM)  buying a rusty car is like dating a girl with a bush! if u like it like that go for it.. :D if u can repair and make it look better then its all the better for u!... |
|
Mar 16, 2009 - 2:56 PM
|
|
|
Enthusiast Joined Mar 13, '09 From ATX Currently Offline Reputation: 0 (0%) |
My neighbor had a micrometer but it's a manual sliding one.
Here are the approx measurements for rotor thickness. Front: 29.5 mm Rear: 15.75 mm |
|
Mar 16, 2009 - 4:49 PM
|
|
|
Enthusiast Joined Mar 13, '09 From ATX Currently Offline Reputation: 0 (0%) |
**Sold** Pending payment...pls lv open until then.
For those asking, I joined here primarily to keep track of the local Celica Meets here in Texas (Austin). I also plan on doing a full 3rd Gen 3s-gte swap into my 2nd gen ST185. Nice to meet you all. |
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 21st, 2025 - 10:56 AM |