Operation: DARKSPYRO, AWD Conversion, Completed. Driven. Sold. Options

[Malek]

Mission: Do it right the first time

Phase 1:
-Gen 3 3sgte swap

Phase 2:
-Complete AWD conversion
-Clean


28 JAN 13
Purchased 1999 Toyota Celica from a private seller in Boulder, CO.
Apparent timing issue and suspected head gasket issue.
Drove it 30 minutes back to Golden, CO with coolant spewing. And when I got back, I beat on it some more.
Back at the shop, wasted no time tearing into it

Had to stop once to let it cool down a little


Ripping into it that night



29 JAN 13
Engine and transmission pulled

Signature Tweak pose


31 JAN 13
Ordered ST205 front clip
-coming with bumper, fenders, hood, lights and a set of projectors
-rear subframe
-rear diff, axles, brakes, drive shaft
-Ton of extra stuff I don't need






1-9 FEB 13
Ordered:
-Berk gen 3 downpipe ceramic coated with wideband bung
-Clutchmasters FX300 assembly for swap
-Triple gauge A pillar (for boost, oil press, wideband)
-Hose for remote oil pressure sender location
-Walbro gss342 + 400-765 kit
Cut a hole in the fire wall for wiring harness

9-15 FEB 13
-Have been collecting parts for the swap
-Installed new Walbro fuel pump

17 FEB 13
-Final decision has been made
FULL AWD Conversion
-I plan on using the GT suspension and GT4 brakes
-Have not decided yet to cut floor pan and weld or make custom brackets


ETA for clip 11 MARCH 13
Until then, I will be researching boost controllers and wheels.

11-18 March 13
PHASE 1: COMPLETE
see page 2
-3rd Gen 3SGTE
-FWD
-OZ Crono

30 April 13
PHASE 2: BEGINS
see page 3 and 4
-Fuel Cell
-AWD
-GT4 Brakes

This post has been edited by Malek: Jan 28, 2018 - 3:53 PM

[mkernz22]

You might as well do it if you have everything....You could just weld the front and rear clips back together, then just weld on what you need for the body / upper half and it would be a legit GT4....I mean the engine, transmission, rear end, and everything is already in there so you wouldn't need to remove anything. It kind of makes sense.

Edit: And where did you order it from?

This post has been edited by mkernz22: Feb 10, 2013 - 4:56 PM

[Malek]

You might as well do it if you have everything....You could just weld the front and rear clips back together, then just weld on what you need for the body / upper half and it would be a legit GT4....I mean the engine, transmission, rear end, and everything is already in there so you wouldn't need to remove anything. It kind of makes sense.

Edit: And where did you order it from?

I'd much rather swap over engine, tranny, rear end..than cut the top half of a car and reweld it to a different bottom half. I am not THAT confident in my welding for all of that

Ordered it from Ho Wong at Sun Shing Trading Company. They're on eBay as new_stars. I lowballed them hard core and they took it

[ClevelandGaint]

Do you have a website or a telephone number where i can order the st205 front clip with engine?

You might as well do it if you have everything....You could just weld the front and rear clips back together, then just weld on what you need for the body / upper half and it would be a legit GT4....I mean the engine, transmission, rear end, and everything is already in there so you wouldn't need to remove anything. It kind of makes sense.

Edit: And where did you order it from?

I'd much rather swap over engine, tranny, rear end..than cut the top half of a car and reweld it to a different bottom half. I am not THAT confident in my welding for all of that

Ordered it from Ho Wong at Sun Shing Trading Company. They're on eBay as new_stars. I lowballed them hard core and they took it